- 您現在的位置：買賣IC網 > PDF目錄367732 > P80CE598 (NXP Semiconductors N.V.) 8-bit microcontroller with on-chip CAN PDF資料下載
參數資料
| 型號： | P80CE598 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 8-bit microcontroller with on-chip CAN |
| 中文描述： | 8位微控制器芯片的CAN |
| 文件頁數： | 64/108頁 |
| 文件大?。?/td> | 507K |
| 代理商： | P80CE598 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁當前第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
1996 Jun 27
64
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xCE598
14 INTERRUPT SYSTEM
External events and the real-time-driven on-chip
peripherals require service by the CPU asynchronous to
the execution of any particular section of code. To tie the
asynchronous activities of these functions to normal
program execution a multiple-source, two-priority-level,
nested interrupt system is provided. Interrupt response
latency is from 2.25
μ
s to 7.5
μ
s when using a 16 MHz
crystal. The latency time strongly depends on the
sequence of instructions executed directly after an
interrupt request. During a CAN-DMA transfer the interrupt
system is disabled (see Section 13.5.17). The P8xCE598
acknowledges interrupt requests from fifteen sources as
follows:
INT0 and INT1: externally via pins 43 and 44
respectively
Timer 0 and Timer 1: from the two internal counters
– If the capture function remains unused and the
Capture Register contents are ‘don't care’ then the
corresponding input pins ‘CTnI’, with ‘n = 0 ... 3’, may
be used as positive and/or negative edge triggered
external interrupts INT2 to INT5. But note that they
can not terminate the Idle mode because the Timer 2
is switched off then.
Timer T2, 8 separate interrupts:
– 4 capture interrupts
– 3 compare interrupts
– An overflow interrupt.
ADC end-of-conversion interrupt
CAN Controller interrupt
UART serial I/O port interrupt.
Each interrupt vectors to a separate location in Program
Memory for its service program. Each source can be
individually enabled or disabled by a corresponding bit in
the IEN0 or IEN1 register, moreover each interrupt may be
programmed to a HIGH or LOW priority level using a
corresponding bit in the IP0 or IP1 register. Also all
enabled sources can be globally disabled or enabled. Both
external interrupts can be programmed to be
level-activated or transition-activated, and an active LOW
level allows ‘wire-ORing’ of several interrupt sources to the
input pin.
相關PDF資料 |
PDF描述 |
|---|---|
| P83CL781 | Low voltage 8-bit microcontrollers with UART and I2C-bus |
| P83CL781HFH | Low voltage 8-bit microcontrollers with UART and I2C-bus |
| P83CL781HFP | Low voltage 8-bit microcontrollers with UART and I2C-bus |
| P83CL782 | Low voltage 8-bit microcontrollers with UART and I2C-bus |
| P83CL782HDH | Low voltage 8-bit microcontrollers with UART and I2C-bus |
相關代理商/技術參數 |
參數描述 |
|---|---|
| P80CE598FFB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
| P80CE598FFB/00,518 | 功能描述:8位微控制器 -MCU 8B MCU ON-CHIP CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P80CE598FFB/00,557 | 功能描述:8位微控制器 -MCU 8B MCU ON-CHIP CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| P80CE598FFB/00551 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-SM-8-BIT MCU+CAN |
| P80CE598FHB | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN |
發布緊急采購，3分鐘左右您將得到回復。