參數資料
型號: P80CE598
廠商: NXP Semiconductors N.V.
英文描述: 8-bit microcontroller with on-chip CAN
中文描述: 8位微控制器芯片的CAN
文件頁數: 45/108頁
文件大小: 507K
代理商: P80CE598
1996 Jun 27
45
Philips Semiconductors
Product specification
8-bit microcontroller with on-chip CAN
P8xCE598
13.5.11 O
UTPUT
C
ONTROL
R
EGISTER
(OCR)
The Output Control Register allows, under software
control, the set-up of different output driver configurations.
This register can be accessed (read/write) if the Reset
Request bit is set HIGH (present). If the CAN-controller is
in the sleep mode (Sleep = HIGH) a recessive level is
output on the CTX0 and CTX1 pins. If the CAN-controller
is in the reset state (Reset Request = HIGH) the output
drivers are floating.
Tables 50 and 51, show the relationship between the bits
of the Output Control Register and the two serial output
pins CTX0 and CTX1 of the P8xCE598 CAN-controller,
connected to the serial bus (see Fig.14).
Table 49
Output Control Register (address 8)
Table 50
Description of the OCR bits
Table 51
Description of the Output Mode bits
7
6
5
4
3
2
1
0
OCTP1
OCTN1
OCPOL1
OCTP0
OCTN0
OCPOL0
OCMODE1
OCMODE0
BIT
SYMBOL
FUNCTION
7
6
5
4
3
2
1
0
OCTP1
OCTN1
OCPOL1
OCTP0
OCTN0
OCPOL0
OCMODE1
OCMODE0
See Tables 51 and 52.
Output Mode
.
These bits select the output mode; see Table 51.
OCMODE1
OCMODE0
DESCRIPTION
1
0
Normal Output Mode
. The bit sequence (TXD) is sent via CTX0, CTX1. TXD is the
data bit to be transmitted. The voltage levels on the output driver pins CTX0 and CTX1
depend on both the driver characteristic programmed by OCTPx, OCTNx (float, pull-up,
pull-down, push-pull) and the output polarity programmed by OCPOLx (see Fig.17).
Clock Output Mode
. For the CTX0 pin this is the same as in Normal Output Mode
(CTX0: bit sequence). However, the data stream to CTX1 is replaced by the transmit
clock (TXCLK). The rising edge of the transmit clock (non-inverted) marks the beginning
of a bit period. The clock pulse width is t
SCL
.
Bi-phase Output Mode
. In contrast to Normal Output Mode the bit representation is
time variant and toggled. If the bus controllers are galvanically decoupled from the
bus-line by a transformer, the bit stream is not allowed to contain a DC component. This
is achieved by the following scheme. During recessive bits all outputs are deactivated
(floating). Dominant bits are sent alternately on CTX0 and CTX1, i.e. the first dominant
bit is sent on CTX0, the second is sent on CTX1, and the third one is sent on CTX0
again, etc.
Test Output Mode.
For the CTX0 pin this is the same as in Normal Output Mode
(CTX0: bit sequence). To measure the delay time of the transmitter and receiver this
mode connects the output of the input comparator (COMP OUT) with the input of the
output driver CTX1. This mode is used for production testing only.
1
1
0
0
0
1
相關PDF資料
PDF描述
P83CL781 Low voltage 8-bit microcontrollers with UART and I2C-bus
P83CL781HFH Low voltage 8-bit microcontrollers with UART and I2C-bus
P83CL781HFP Low voltage 8-bit microcontrollers with UART and I2C-bus
P83CL782 Low voltage 8-bit microcontrollers with UART and I2C-bus
P83CL782HDH Low voltage 8-bit microcontrollers with UART and I2C-bus
相關代理商/技術參數
參數描述
P80CE598FFB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN
P80CE598FFB/00,518 功能描述:8位微控制器 -MCU 8B MCU ON-CHIP CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80CE598FFB/00,557 功能描述:8位微控制器 -MCU 8B MCU ON-CHIP CAN RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
P80CE598FFB/00551 制造商:未知廠家 制造商全稱:未知廠家 功能描述:IC-SM-8-BIT MCU+CAN
P80CE598FHB 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:8-bit microcontroller with on-chip CAN