參數資料
型號: NAND04GW3C2AN6E
廠商: 意法半導體
英文描述: 4Gbit, 2112 Byte Page, 3V, Multi-level NAND Flash Memory
中文描述: 4Gbit的,2112字節的頁,3V供電,多級NAND閃存
文件頁數: 22/51頁
文件大?。?/td> 374K
代理商: NAND04GW3C2AN6E
6 Device operations
NAND04GA3C2A, NAND04GW3C2A
22/51
6.6
Sequential Input
To input data sequentially the addresses must be sequential and remain in one block.
For Sequential Input each Page Program operation comprises five steps:
1.
One bus cycle is required to setup the Page Program (Sequential Input) command (see
Table 8
).
2.
Five bus cycles are then required to input the program address (refer to
Table 6
).
3.
The data is then loaded into the Data Registers.
4.
One bus cycle is required to issue the Page Program confirm command to start the
P/E/R Controller. The P/E/R will only start if the data has been loaded in step 3.
5.
The P/E/R Controller then programs the data into the array.
6.7
Random Data input
During a Sequential Input operation, the next sequential address to be programmed can be
replaced by a random address, by issuing a Random Data Input command. The following
two steps are required to issue the command:
1.
One bus cycle is required to setup the Random Data Input command (see
Table 8
).
2.
Two bus cycles are then required to input the new column address (refer to
Table 6
).
Random Data Input can be repeated as often as required in any given page.
Once the program operation has started the Status Register can be read using the Read
Status Register command. During program operations the Status Register will only flag
errors for bits set to '1' that have not been successfully programmed to '0'.
During the program operation, only the Read Status Register and Reset commands will be
accepted, all other commands will be ignored.
Once the program operation has completed the P/E/R Controller bit SR6 is set to ‘1’ and the
Ready/Busy signal goes High.
The device remains in Read Status Register mode until another valid command is written to
the Command Interface.
Figure 8.
Page Program Operation
I/O
RB
Address Inputs
SR0
ai08659
Data Input
10h
70h
80h
Page Program
Setup Code
Confirm
Code
Read Status Register
Busy
(Program Busy time)
相關PDF資料
PDF描述
NAND128R3A2AZA1 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND128W3A0AV6 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND256R3A0AZB6 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND128W4A0CZA6E 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
NAND128R4A2BZA1E 128 Mbit, 256 Mbit, 512 Mbit, 1 Gbit (x8/x16) 528 Byte/264 Word Page, 1.8V/3V, NAND Flash Memories
相關代理商/技術參數
參數描述
NAND04GW3C2BN6E 功能描述:IC FLASH 4GBIT 48TSOP RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:576 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:512M(64M x 8) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP 包裝:托盤 其它名稱:497-5040
NAND08GAH0BZA5E 功能描述:IC FLASH 8GBIT 52MHZ 169LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:576 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:512M(64M x 8) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP 包裝:托盤 其它名稱:497-5040
NAND08GAH0FZC5E 功能描述:IC FLASH 8GBIT 52MHZ 153LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:576 系列:- 格式 - 存儲器:閃存 存儲器類型:閃存 - NAND 存儲容量:512M(64M x 8) 速度:- 接口:并聯 電源電壓:2.7 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:48-TFSOP(0.724",18.40mm 寬) 供應商設備封裝:48-TSOP 包裝:托盤 其它名稱:497-5040
NAND08GAH0JZC5E 功能描述:IC FLASH 8GBIT 52MHZ 153LFBGA RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:- 標準包裝:1,000 系列:- 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:4K (512 x 8) 速度:400kHz 接口:I²C,2 線串口 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-SOIC(0.173",4.40mm 寬) 供應商設備封裝:8-MFP 包裝:帶卷 (TR)
NAND08GR3B4CZL6E 制造商:Micron Technology Inc 功能描述:NAND - Trays