- 您現在的位置：買賣IC網 > PDF目錄4035 > MC8640DHX1250HE (Freescale Semiconductor)IC DUAL CORE PROCESSOR 1023-CBGA PDF資料下載
參數資料
| 型號： | MC8640DHX1250HE |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 22/130頁 |
| 文件大小： | 0K |
| 描述： | IC DUAL CORE PROCESSOR 1023-CBGA |
| 標準包裝： | 1 |
| 系列： | MPC86xx |
| 處理器類型： | 32-位 MPC86xx PowerPC |
| 速度： | 1.25GHz |
| 電壓： | 1.05V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 1023-BCBGA，F(xiàn)CCBGA |
| 供應商設備封裝： | 1023-FCCBGA（33x33） |
| 包裝： | 托盤 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁
MPC8640 and MPC8640D Integrated Host Processor Hardware Specifications, Rev. 3
118
Freescale Semiconductor
System Design Information
designer place at least one decoupling capacitor at each OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren,
and VDD_PLAT pin of the device. These decoupling capacitors should receive their power from separate
OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT and GND power planes in the PCB,
utilizing short traces to minimize inductance. Capacitors may be placed directly under the device using a
standard escape pattern. Others may surround the part.
These capacitors should have a value of 0.01 or 0.1 F. Only ceramic SMT (surface mount technology)
capacitors should be used to minimize lead inductance, preferably 0402 or 0603 sizes.
In addition, it is recommended that there be several bulk storage capacitors distributed around the PCB,
feeding the OVDD, Dn_GVDD, LVDD, TVDD, VDD_Coren, and VDD_PLAT planes, to enable quick
recharging of the smaller chip capacitors. They should also be connected to the power and ground planes
through two vias to minimize inductance. Suggested bulk capacitors—100–330 F (AVX TPS tantalum
or Sanyo OSCON).
20.4
SerDes Block Power Supply Decoupling Recommendations
The SerDes block requires a clean, tightly regulated source of power (SVDD and XVDD_SRDSn) to ensure
low jitter on transmit and reliable recovery of data in the receiver. An appropriate decoupling scheme is
outlined below.
Only surface mount technology (SMT) capacitors should be used to minimize inductance. Connections
from all capacitors to power and ground should be done with multiple vias to further reduce inductance.
First, the board should have at least 10
× 10-nF SMT ceramic chip capacitors as close as possible
to the supply balls of the device. Where the board has blind vias, these capacitors should be placed
directly below the chip supply and ground connections. Where the board does not have blind vias,
these capacitors should be placed in a ring around the device as close to the supply and ground
connections as possible.
Second, there should be a 1-F ceramic chip capacitor on each side of the device. This should be
done for all SerDes supplies.
Third, between the device and any SerDes voltage regulator there should be a 10-F, low
equivalent series resistance (ESR) SMT tantalum chip capacitor and a 100-F, low ESR SMT
tantalum chip capacitor. This should be done for all SerDes supplies.
20.5
Connection Recommendations
To ensure reliable operation, it is highly recommended to connect unused inputs to an appropriate signal
level. In general all unused active low inputs should be tied to OVDD, Dn_GVDD, LVDD, TVDD,
VDD_Coren, and VDD_PLAT, XVDD_SRDSn, and SVDD as required and unused active high inputs should
be connected to GND. All NC (no-connect) signals must remain unconnected.
The following list explains the special cases:
DDR—If one of the DDR ports is not being used the power supply pins for that port can be
connected to ground so that there is no need to connect the individual unused inputs of that port to
ground. Note that these power supplies can only be powered up again at reset for functionality to
occur on the DDR port. Power supplies for other functional buses should remain powered.
相關PDF資料 |
PDF描述 |
|---|---|
| IDT7007S20PF8 | IC SRAM 256KBIT 20NS 80TQFP |
| XC4028XL-09HQ208C | IC FPGA C-TEMP 3.3V 208-HQFP |
| XC4028XL-09BG352C | IC FPGA C-TEMP 3.3V 352-MBGA |
| MPC8572ECVTAVNE | MPU POWERQUICC III 1023FCPBGA |
| MC68EN360RC25L | IC MPU QUICC 32BIT 25MHZ 241-PGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC8640DHX1250N | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
| MC8640DTHX1000H | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications |
| MC8640DTHX1000HC | 功能描述:微處理器 - MPU G8 REV2.1 1.05V -40/105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC8640DTHX1000HE | 功能描述:微處理器 - MPU G8 REV 3.0 1.05V -40/105C RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| MC8640DTHX1000N | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Integrated Host Processor Hardware Specifications Addendum for the MC8640xTxxyyyyaC Series |
發布緊急采購，3分鐘左右您將得到回復。