參數資料
型號： MC68HC916X1
廠商： Motorola, Inc.
英文描述： 16-Bit Modular Microcontroller(16位模塊化微控制器)
中文描述： 16位微控制器模塊（16位模塊化微控制器）
文件頁數： 23/172頁
文件大?。?/td> 1035K
代理商： MC68HC916X1
MC68HC916X1
MC68HC916X1TS/D
MOTOROLA
23
The synthesizer locks when the VCO frequency is equal to f
ref
. Lock time is affected by the filter
time constant and by the amount of difference between the two comparator inputs. Whenever a
comparator input changes, the synthesizer must relock. Lock status is shown by the SLOCK bit in
SYNCR. During power-up, the MCU does not come out of reset until the synthesizer locks. Crystal
type, characteristic frequency, and layout of external oscillator circuitry affect lock time.
When the clock synthesizer is used, SYNCR determines operating frequency and certain operating
parameters. The W and Y[5:0] bits are located in the PLL feedback path, enabling frequency mul-
tiplication by a factor of up to 256. When the W or Y values change, VCO frequency changes, and
there is a VCO relock delay. The SYNCR X bit controls a divide-by circuit that is not in the synthe-
sizer feedback loop. When X = 0 (reset state), a divide-by-four circuit is enabled, and the system
clock frequency is one-fourth the VCO frequency (f
VCO
). When X = 1, a divide-by-two circuit is en-
abled, and system clock frequency is one-half the VCO frequency (f
VCO
). There is no relock delay
when clock speed is changed by the X bit.
Clock frequency is determined by SYNCR bit settings as follows:
The reset state of SYNCR ($3F00) results in a power-on f
sys
of 16.78 MHz when the f
ref
is 4.194
MHz.
For the device to perform correctly, the clock and frequency selected by the W, X, and Y bits must
be within the limits specified for the MCU.
Internal VCO frequency is determined by the following equations:
or
3.3.3 Clock Control
The clock control circuits determine system clock frequency and clock operation under special cir-
cumstances, such as loss of synthesizer reference or low-power mode. Clock source is determined
by the logic state of the MODCLK pin during reset.
When the on-chip clock synthesizer is used, system clock frequency is controlled by the bits in the
upper byte of SYNCR. Bits in the lower byte show the status of, or control the operation of, internal
and external clocks. Because the CPU16 always operates in supervisor mode, SYNCR can be read
or written at any time.
1. Ensure that initialization software does not change the value of this bit. It should always be zero.
SYNCR
— Clock Synthesizer Control Register
$YFFA04
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
W
X
Y[5:0]
EDIV
0
0
RSVD
1
SLOCK
RSVD
1
STSCIM
STEXT
RESET:
0
0
1
1
1
1
1
1
0
0
0
0
U
0
0
0
fsys
fref
128
--------- 4 Y
1
+
)
22W
(
X
+
)
)
]
=
fVCO
4fsys
if X = 0
=
fVCO
2fsys if X = 1
=
相關PDF資料
PDF描述
MC68HC9D60 Advance Information - Rev 4.0
MC68HC12D60 Advance Information - Rev 4.0
MC68HCL05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HSC05C8A 8-Bit Microcontroller Units (MCU).(8位微控制器)
MC68HCP11 8-Bit Microcontrollers
相關代理商/技術參數
參數描述
MC68HC98LJ12CFU 制造商:Rochester Electronics LLC 功能描述: 制造商:Freescale Semiconductor 功能描述:
MC68HC98LJ12CFUE 功能描述:8位微控制器 -MCU 8 BIT MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HC9S08RC60 L33R DIE 制造商:Motorola Inc 功能描述:
MC68HCP11A1CFN3 功能描述:8位微控制器 -MCU 8-bit HCMOS single chip MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
MC68HCP11A1FN 制造商:MOTORALA 功能描述:
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*