參數資料
型號: MC68HC705T16B
廠商: MOTOROLA INC
元件分類: 微控制器/微處理器
英文描述: 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP56
封裝: PLASTIC, SDIP-56
文件頁數: 10/128頁
文件大?。?/td> 734K
代理商: MC68HC705T16B
MC68HC05T16
MOTOROLA
12-1
LOW POWER MODES
12
LOW POWER MODES
The STOP and WAIT instructions have different effects on the Programmable Timer, M-Bus, Pulse
Accumulator, PWM, OSD, and ADC. These are discussed in the following paragraphs.
12.1
Stop Mode
This is the lowest power consumption mode for the MCU. When the processor executes the STOP
instruction, the internal clock is turned off. This halts all internal CPU processing, including the
operation of the Programmable Timer, M-Bus, Pulse Accumulator, PWM, OSD, and ADC. The I bit
in the Condition Code register is cleared to enable external interrupt IRQ. All registers and
memory remain unaltered, and all input/output lines remain unchanged.
The MCU is exited from Stop mode by an interrupt on IRQ, or any resets (logic low on RESET pin
or a power-on reset). On exit from Stop mode, the program counter is loaded with the
corresponding interrupt vector (see Table 5-1). The effects of the Stop mode on each of the MCU
peripheral systems are below.
12.1.1
Timer during Stop Mode
When Stop mode is entered, the timer counter stops counting (the internal processor clock is
stopped) and remains at that particular count value until Stop mode is exited. If the exit was
caused by reset, the counter is forced to $FFFC. If the Stop mode is exited by an interrupt IRQ,
the counter resumes counting from the value when it entered the Stop mode. Another feature of
the programmable timer in the Stop mode is, that if at least one valid input capture edge occurs at
the TCAP pin, the input capture detect circuitry is armed. This action does not set any timer ags
or “wake up” the MCU, but when the MCU does “wake up” there will be an active input capture ag
(and data) from that rst valid edge which occurred during the Stop mode. Notice that an exit by
a reset will reset the entire MCU and thus, this function on the TCAP will not happen.
TPG
105
相關PDF資料
PDF描述
MC68HC05T16B 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC705V8CFU 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQFP64
MC68HC705V8B 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PDIP56
MC68HC705V8FN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
MC68HC705V8CFN 8-BIT, OTPROM, 2.1 MHz, MICROCONTROLLER, PQCC68
相關代理商/技術參數
參數描述
MC68HC706P6ACDW 制造商:Motorola Inc 功能描述:
MC68HC708MP16CFU 制造商:MAJOR 功能描述:
MC68HC711D3CFBE2 制造商:Freescale Semiconductor 功能描述:
MC68HC711D3CFN2 功能描述:IC MCU 2MHZ 4K OTP 44-PLCC RoHS:否 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:HC11 其它有關文件:STM32F101T8 View All Specifications 特色產品:STM32 32-bit Cortex MCUs 標準包裝:490 系列:STM32 F1 核心處理器:ARM? Cortex?-M3 芯體尺寸:32-位 速度:36MHz 連通性:I²C,IrDA,LIN,SPI,UART/USART 外圍設備:DMA,PDR,POR,PVD,PWM,溫度傳感器,WDT 輸入/輸出數:26 程序存儲器容量:64KB(64K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:10K x 8 電壓 - 電源 (Vcc/Vdd):2 V ~ 3.6 V 數據轉換器:A/D 10x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:36-VFQFN,36-VFQFPN 包裝:托盤 配用:497-10030-ND - STARTER KIT FOR STM32497-8853-ND - BOARD DEMO STM32 UNIV USB-UUSCIKSDKSTM32-PL-ND - KIT IAR KICKSTART STM32 CORTEXM3497-8512-ND - KIT STARTER FOR STM32F10XE MCU497-8505-ND - KIT STARTER FOR STM32F10XE MCU497-8304-ND - KIT STM32 MOTOR DRIVER BLDC497-6438-ND - BOARD EVALUTION FOR STM32 512K497-6289-ND - KIT PERFORMANCE STICK FOR STM32MCBSTM32UME-ND - BOARD EVAL MCBSTM32 + ULINK-MEMCBSTM32U-ND - BOARD EVAL MCBSTM32 + ULINK2更多... 其它名稱:497-9032STM32F101T8U6-ND
MC68HC711D3CFNE2 功能描述:8位微控制器 -MCU 8B OTP 192RAM 2 MHZ RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT