參數資料
型號: MC68HC11D0CFNE3R
廠商: Freescale Semiconductor
文件頁數: 43/124頁
文件大?。?/td> 0K
描述: MCU 8-BIT 192 RAM 3MHZ 44-PLCC
標準包裝: 450
系列: HC11
核心處理器: HC11
芯體尺寸: 8-位
速度: 3MHz
連通性: SCI,SPI
外圍設備: POR,WDT
輸入/輸出數: 26
程序存儲器類型: ROMless
RAM 容量: 192 x 8
電壓 - 電源 (Vcc/Vdd): 4.5 V ~ 5.5 V
振蕩器型: 內部
工作溫度: -40°C ~ 85°C
封裝/外殼: 44-LCC(J 形引線)
包裝: 帶卷 (TR)
CENTRAL PROCESSING UNIT
TECHNICAL DATA
3-5
tions. Shift and rotate instructions operate with and through the carry bit to facilitate
multiple-word shift operations.
3.1.6.2 Overflow (V)
The overflow bit is set if an operation causes an arithmetic overflow. Otherwise, the V
bit is cleared.
3.1.6.3 Zero (Z)
The Z bit is set if the result of an arithmetic, logic, or data manipulation operation is
zero. Otherwise, the Z bit is cleared. Compare instructions do an internal implied sub-
traction and the condition codes, including Z, reflect the results of that subtraction. A
few operations (INX, DEX, INY, and DEY) affect the Z bit and no other condition flags.
For these operations, only = and - conditions can be determined.
3.1.6.4 Negative (N)
The N bit is set if the result of an arithmetic, logic, or data manipulation operation is
negative (MSB = 1). Otherwise, the N bit is cleared. A result is said to be negative if its
most significant bit (MSB) is a one. A quick way to test whether the contents of a mem-
ory location has the MSB set is to load it into an accumulator and then check the status
of the N bit.
3.1.6.5 Interrupt Mask (I)
The interrupt request (IRQ) mask (I bit) is a global mask that disables all maskable in-
terrupt sources. While the I bit is set, interrupts can become pending, but the operation
of the CPU continues uninterrupted until the I bit is cleared. After any reset, the I bit is
set by default and can only be cleared by a software instruction. When an interrupt is
recognized, the I bit is set after the registers are stacked, but before the interrupt vector
is fetched. After the interrupt has been serviced, a return from interrupt instruction is
normally executed, restoring the registers to the values that were present before the
interrupt occurred. Normally, the I bit is zero after a return from interrupt is executed.
Although the I bit can be cleared within an interrupt service routine, “nesting” interrupts
in this way should only be done when there is a clear understanding of latency and of
the arbitration mechanism. Refer to SECTION 5 RESETS AND INTERRUPTS.
3.1.6.6 Half Carry (H)
The H bit is set when a carry occurs between bits 3 and 4 of the arithmetic logic unit
during an ADD, ABA, or ADC instruction. Otherwise, the H bit is cleared. Half carry is
used during BCD operations.
3.1.6.7 X Interrupt Mask (X)
The XIRQ mask (X) bit disables interrupts from the pin. After any reset, X is set by de-
fault and must be cleared by a software instruction. When an interrupt is recognized,
the X and I bits are set after the registers are stacked, but before the interrupt vector
is fetched. After the interrupt has been serviced, an RTI instruction is normally execut-
ed, causing the registers to be restored to the values that were present before the in-
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
相關PDF資料
PDF描述
MC68HC11D0CFNE2R MCU 8-BIT 192 RAM 2MHZ 44-PLCC
MC68HC11D0CFNE2 MCU 8-BIT 192 RAM 2MHZ 44-PLCC
VI-BNX-CU-F3 CONVERTER MOD DC/DC 5.2V 200W
MC68HC11D0CFBE3R MCU 8-BIT 192 RAM 3MHZ 44-QFP
MC68HC11D0CFBE2 MCU 8-BIT 192 RAM 2MHZ 44-QFP
相關代理商/技術參數
參數描述
MC68HC11D0CP3 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
MC68HC11D0FB 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
MC68HC11D0FN 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
MC68HC11D0FNR2 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller
MC68HC11D0P 制造商:未知廠家 制造商全稱:未知廠家 功能描述:8-Bit Microcontroller