- 您現在的位置：買賣IC網 > PDF目錄371048 > MC68HC11A8VCFU2 (MOTOROLA INC) HCMOS Single-Chip Microcontroller PDF資料下載
參數資料
| 型號： | MC68HC11A8VCFU2 |
| 廠商： | MOTOROLA INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | HCMOS Single-Chip Microcontroller |
| 中文描述： | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | QFP-64 |
| 文件頁數： | 84/158頁 |
| 文件大小： | 776K |
| 代理商： | MC68HC11A8VCFU2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁當前第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
MOTOROLA
9-4
RESETS, INTERRUPTS, AND LOW POWER MODES
MC68HC11A8
TECHNICAL DATA
9
9.1.2.5 Real-Time Interrupt
The real time interrupt flag is cleared and automatic hardware interrupts are masked.
The rate control bits are cleared after reset and may be initialized by software before
the real time interrupt system is used.
9.1.2.6 Pulse Accumulator
The pulse accumulator system is disabled at reset so that the PAI input pin defaults to
being a general purpose input pin.
9.1.2.7 COP
The COP watchdog system is enabled if the NOCOP control bit in the system config-
uration control register (EEPROM cell) is clear, and disabled if NOCOP is set. The
COP rate is set for the shortest duration timeout.
9.1.2.8 SCI Serial l/O
The reset condition of the SCI system is independent of the operating mode. At reset,
the SCI baud rate is indeterminate and must be established by a software write to the
BAUD register. All transmit and receive interrupts are masked and both the transmitter
and receiver are disabled so the port pins default to being general purpose l/O lines.
The SCI frame format is initialized to an 8-bit character size. The send break and re-
ceiver wake up functions are disabled. The TDRE and TC status bits in the SCI status
register are both set, indicating that there is no transmit data in either the transmit data
register or the transmit serial shift register. The RDRF, IDLE, OR, NF, and FE receive-
related status bits are all cleared.
Note that upon reset in special bootstrap mode execution begins in the 192 byte boot
ROM. This firmware sets port D to wire-OR mode, establishes a baud rate, and en-
ables the SCI receiver and transmitter.
9.1.2.9 SPI Serial l/O
The SPI system is disabled by reset. The port pins associated with this function default
to being general purpose l/O lines.
9.1.2.10 A/D Converter
The A/D converter system configuration is indeterminate after reset. The conversion
complete flag is cleared by reset. The ADPU bit is cleared by reset thus disabling the
A/D system.
9.1.2.11 System
The EEPROM programming controls are all disabled so the memory system is config-
ured for normal read operation. The highest priority I interrupt defaults to being the ex-
ternal IRQ pin by PSEL[3:0] equal to 0:1:0:1. The IRQ interrupt pin is configured for
level sensitive operation (for wire-OR systems). The RBOOT, SMOD, and MDA bits in
the HPRIO register reflect the status of the MODB and MODA inputs at the rising edge
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC11A1VFU2 | HCMOS Single-Chip Microcontroller |
| MC68HC11E0CB2 | Microcontrollers |
| MC68S711E9CFN2 | Microcontrollers |
| MC68HC711E20FS3 | Microcontrollers |
| MC68L11E20FU2 | Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC11AOFNR2 | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Motorola Inc 功能描述: 制造商:MOTOROLA 功能描述: |
| MC68HC11AX | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:8-Bit Microcontrollers |
| MC68HC11C0 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontroller |
| MC68HC11C0CFN2 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontroller |
| MC68HC11C0CFN3 | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:8-Bit Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。