- 您現在的位置：買賣IC網 > PDF目錄45220 > MC68HC05F8FU (FREESCALE SEMICONDUCTOR INC) 8-BIT, MROM, 1.8 MHz, MICROCONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | MC68HC05F8FU |
| 廠商： | FREESCALE SEMICONDUCTOR INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, MROM, 1.8 MHz, MICROCONTROLLER, PQFP64 |
| 封裝： | PLASTIC, QFP-64 |
| 文件頁數： | 12/126頁 |
| 文件大?。?/td> | 1084K |
| 代理商： | MC68HC05F8FU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁
MC68HC05F8
MOTOROLA
12-5
OPERATING MODES
12
LAT - Latch EPROM Data and Address
1 (set)
–
EPROM address and data buses congured for programming.
0 (clear) –
EPROM address and data buses congured for normal reads.
LAT causes address and data buses to be latched when a write to EPROM is carried out. The
EPROM cannot be read if LAT=1. This bit should not be set unless a programming voltage is
applied to the VPP pin.
EPGM - EPROM Programming Mode Enable
1 (set)
–
Programming power connected to the EPROM array.
0 (clear) –
Programming power disconnected from the EPROM array.
LAT and EPMG cannot be set on the same write operation. EPMG can only be set if LAT is set.
EPMG is automatically cleared when LAT is cleared.
12.3.2
EPROM Programming Sequence
In the bootstrap, the user program contained in an external EPROM is copied into the internal
EPROM of the MC68HC705F8 device (see Figure 12-5). The MC68HC705F8 device is inserted
into the programming circuit as shown in Figure 12-5. Programming routine is selected via mode
switch S1, and +5V and VPP power is applied to the programming circuitry. The MCU is removed
from the reset state and placed in the run mode of operation via switch S4, and MCU control is
transferred to the bootstrap ROM. The selected programming routine is then executed.
Programming sequence of events are as follows:
1) Place switch S4 to RESET position (switch close).
2) Select programming routine via switches S1.
3) Apply +5 V and VPP power to programming circuitry.
4) Place switch S4 to RUN position (switch open).
5) Programming routine is executed.
6) Place switch S4 to RESET position.
7) Remove VPP and +5 V power, or select and run new routine.
Once the bootstrap mode is entered, mode switch setting is scanned to establish the routine to be
executed. The routines are:
–
Program and Verify EPROM
–
Verify EPROM Contents
Note:
When programming the window part MC68HC705F8, the window should be covered
up to prevent erratic device behaviour.
TPG
107
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
I
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
c
..
.
F
re
e
sc
a
le
S
e
m
ic
o
n
d
u
c
to
r,
In
c
..
.
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
相關PDF資料 |
PDF描述 |
|---|---|
| MC68HC05I8FU | 8-BIT, MROM, 2 MHz, MICROCONTROLLER, PQFP64 |
| MC68HC05J1DW | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO20 |
| MC68HC05J1CP | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDIP20 |
| MC68HC05J5AJDWR2 | 8-BIT, MROM, 2.1 MHz, MICROCONTROLLER, PDSO16 |
| MC68HRC05J5ADWR3 | 8-BIT, MROM, MICROCONTROLLER, PDSO20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC68HC05J1 | 制造商:MOTOROLA 制造商全稱:Motorola, Inc 功能描述:HCMOS MICROCONTROLLER UNIT |
| MC68HC05J1A | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACDW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ACP | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
| MC68HC05J1ADW | 制造商:FREESCALE 制造商全稱:Freescale Semiconductor, Inc 功能描述:Microcontrollers |
發布緊急采購，3分鐘左右您將得到回復。