- 您現在的位置：買賣IC網 > PDF目錄11545 > MC33889DEG (Freescale Semiconductor)IC SYSTEM BASE W/CAN 28-SOIC PDF資料下載
參數資料
| 型號： | MC33889DEG |
| 廠商： | Freescale Semiconductor |
| 文件頁數： | 18/59頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SYSTEM BASE W/CAN 28-SOIC |
| 標準包裝： | 24 |
| 控制器類型： | 系統基礎芯片 |
| 接口： | CAN |
| 電源電壓： | 5.5 V ~ 18 V |
| 電流 - 電源： | 45mA |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC W |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁
Analog Integrated Circuit Device Data
Freescale Semiconductor
25
33889
FUNCTIONAL DESCRIPTION
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
VOLTAGE REGULATOR TWO (V2)
The V2 pin is the input sense for the V2 regulator. It is connected to the external series pass transistor. V2 is also the 5.0 V
supply of the internal CAN interface. It is possible to connect V2 to an external 5.0 V regulator or to the VDD output when no
external series pass transistor is used. In this case, the V2CTRL pin must be left open.
RTH (RTH)
Pin for the connection of the bus termination resistor to CANH
RTL (RTL)
Pin for the connection of the bus termination resistor to CANL
CAN HIGH AND CAN LOW OUTPUTS
(CANH AND CANL)
The CAN High and CAN Low pins are the interfaces to the CAN bus lines. They are controlled by TXD input level, and the
state of CANH and CANL is reported through RXD output.
SYSTEM CLOCK (SCLK)
SCLK is the Serial Data Clock input pin of the serial peripheral interface.
MASTER IN/SLAVE OUT (MISO
MISO is the Master In Slave Out pin of the serial peripheral interface. Data is sent from the SBC to the microcontroller through
the MISO pin.
MASTER OUT/SLAVE IN (MOSI)
MOSI is the Master Out Slave In pin of the serial peripheral interface. Control data from a microcontroller is received through
this pin.
CHIP SELECT (CS)
CS is the Chip Select pin of the serial peripheral interface. When this pin is LOW, the SPI port of the device is selected.
WATCH DOG (WDOG)
The Watchdog output pin is asserted LOW to flag that the software watchdog has not been properly triggered.
FUNCTIONAL INTERNAL BLOCK DESCRIPTION
DEVICE SUPPLY
The device is supplied from the battery line through the VSUP pin. An external diode is required to protect against negative
transients and reverse battery. It can operate from 4.5 V and under the jump start condition at 27 V DC. This pin sustains standard
automotive voltage conditions such as load dump at 40 V. When VSUP falls below 3.0 V typical, the MC33889 detects it and
stores the information in the SPI register, in a bit called “BATFAIL”. This detection is available in all operation modes.
VDD1 VOLTAGE REGULATOR
VDD1 Regulator is a 5.0 V output voltage with total current capability of 200 mA. It includes a voltage monitoring circuitry
associated with a reset function. The VDD1 regulator is fully protected against overcurrent, short-circuit and has overtemperature
detection warning flags and shutdown with hysteresis.
V2 REGULATOR
V2 Regulator circuitry is designed to drive an external path transistor in order to increase output current flexibility. Two pins
are used: V2 and V2CTRL. Output voltage is 5.0 V and is realized by a tracking function of the VDD1 regulator. A recommended
ballast transistor is the MJD32C. Other transistors might be used, however depending upon the PNP gain, an external resistor
capacitor network might be connected between the emitter and base of the PNP. The use of external ballast is optional (refer to
simplified typical application). The state of V2 is reported into the IOR register (if V2 is below 4.5 V typical, or in cases of overload
or short-circuit).
相關PDF資料 |
PDF描述 |
|---|---|
| VE-22V-IX-S | CONVERTER MOD DC/DC 5.8V 75W |
| V72A12C400B3 | CONVERTER MOD DC/DC 12V 400W |
| VI-23B-IX-S | CONVERTER MOD DC/DC 95V 75W |
| V48C5M75BL3 | CONVERTER MOD DC/DC 5V 75W |
| V48C5M75BG2 | CONVERTER MOD DC/DC 5V 75W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC33889DPEG | 功能描述:CAN 接口集成電路 SBC-LITE-LS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33889DPEGR2 | 功能描述:CAN 接口集成電路 SBC-LITE-LS-CAN RoHS:否 制造商:Texas Instruments 類型:Transceivers 工作電源電壓:5 V 電源電流: 工作溫度范圍:- 40 C to + 85 C 封裝 / 箱體:SOIC-8 封裝:Tube |
| MC33889DW | 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| MC33889DWR2 | 功能描述:IC SYSTEM BASE W/CAN 28-SOIC RoHS:否 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
| MC33895FC | 功能描述:IC H-BRIDGE QUAD W/LIN 32-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。