Use the following procedure for turning the power on or off. If not using the A/" />
參數資料
型號: MB91F482PMC-GE1
廠商: Fujitsu Semiconductor America Inc
文件頁數: 20/94頁
文件大?。?/td> 0K
描述: IC MCU 256KB FLASH 100-LQFP
標準包裝: 1
系列: FR MB91480
核心處理器: FR60 RISC
芯體尺寸: 32-位
速度: 80MHz
連通性: I²C,FIFO,SIO
外圍設備: DMA,PWM,WDT
輸入/輸出數: 77
程序存儲器容量: 256KB(256K x 8)
程序存儲器類型: 閃存
RAM 容量: 16K x 8
電壓 - 電源 (Vcc/Vdd): 4 V ~ 5.5 V
數據轉換器: A/D 14x8/10b
振蕩器型: 外部
工作溫度: -40°C ~ 85°C
封裝/外殼: 100-LQFP
包裝: 托盤
其它名稱: 865-1097
MB91470/480 Series
27
Order of power turning ON/OFF
Use the following procedure for turning the power on or off. If not using the A/D converter, connect AVCC =VCC
and AVSS = VSS. Turn on the power supply in the sequence VCC
→ AVCC → AVRH, and turn off the power in
the reverse sequence.
Source oscillation input when turning on the power
When turning the power on, maintain the clock input until the device is released from the oscillation stabilization
wait state.
Cautions for operation during PLL clock mode
Even if the oscillator comes off or the clock input stops with the PLL clock selected for MB91470/480 series,
MB91470/480 series may continue to operate at the free-run frequency of the PLL’s internal self-oscillating
oscillator circuit.
Performance of this operation, however, cannot be guaranteed.
Using an external clock
When using an external clock, you must always input clock signals with opposite phase from X0 pin to X1 pin
simultaneously. However, as the X1 pin halts with an output at the "H" level during stop mode, insert a resistor
of approximately 1 k
externally to prevent a conflict between the two outputs if using stop mode (oscillation
stop mode).
The figure below shows an example of how to use an external clock.
C pin
As MB91470/480 series includes an internal regulator, always connect a bypass capacitor of approximately
4.7
F to the C pin for use by the regulator.
Software reset on the synchronous mode
Be sure to meet the following two conditions before setting 0 to the SRST bit of STCR (standby control register)
when the software reset is used on the synchronous mode.
Set the interrupt enable flag (I-Flag) to interrupts disabled (I-Flag=0).
Not used NMI
X0
X1
MB91470/480
series
Example of Using an External Clock
C
4.7
F
GND
VSS
MB91470/480
series
相關PDF資料
PDF描述
ADUC7036CCPZ-RL IC MCU 96K FLASH DUAL 48LFCSP
VI-J30-IW-F2 CONVERTER MOD DC/DC 5V 100W
ADUC7036DCPZ-RL IC MCU 96K FLASH DUAL 48LFCSP
ADUC7036BCPZ-RL IC SENSOR AUTO 96K FLASH 48LFCSP
ADUC7019BCPZ62IRL7 IC MCU 12BIT 1MSPS I2C 40-LFCSP
相關代理商/技術參數
參數描述
MB91F487 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontrollers
MB91F487PMC-GE1 功能描述:IC MCU 512KB FLASH 100-LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:FR MB91480 標準包裝:38 系列:Encore!® XP® 核心處理器:eZ8 芯體尺寸:8-位 速度:5MHz 連通性:IrDA,UART/USART 外圍設備:欠壓檢測/復位,LED,POR,PWM,WDT 輸入/輸出數:16 程序存儲器容量:4KB(4K x 8) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):2.7 V ~ 3.6 V 數據轉換器:- 振蕩器型:內部 工作溫度:-40°C ~ 105°C 封裝/外殼:20-SOIC(0.295",7.50mm 寬) 包裝:管件 其它名稱:269-4116Z8F0413SH005EG-ND
MB91F492PMC-GE1 功能描述:IC MCU 256KB FLASH FR60 LFQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器, 系列:FR MB91490 產品培訓模塊:The Ultra-Low Power MSP430 MSP430 Overview MSP430 Design Tools MSP430 Peripherals MSP430x2xx/4xx and Wireless Overview Portable Medical Solutions with MSP430 MSP430 for Utility Metering Solutions MSP430: How to JTAG MSP430, How To Use the Clock System Grace Software Graphical User Interface MCU Overview Driver Library MSP430Ware Overview 標準包裝:1 系列:MSP430x4xx 核心處理器:RISC 芯體尺寸:16-位 速度:8MHz 連通性:SPI,UART/USART 外圍設備:欠壓檢測/復位,LCD,POR,PWM,WDT 輸入/輸出數:48 程序存儲器容量:32KB(32K x 8 + 256B) 程序存儲器類型:閃存 EEPROM 大小:- RAM 容量:1K x 8 電壓 - 電源 (Vcc/Vdd):1.8 V ~ 3.6 V 數據轉換器:A/D 8x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:100-LQFP 包裝:Digi-Reel® 其它名稱:296-26232-6
MB91F585 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Motor Control MCU for Electric (EV) and Hybrid Electric Vehicles (HEV)
MB91F587 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Motor Control MCU for Electric (EV) and Hybrid Electric Vehicles (HEV)