- 您現在的位置：買賣IC網 > PDF目錄98010 > MB90F574/APFF (FUJITSU LTD) 16-BIT, FLASH, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB90F574/APFF |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 31/120頁 |
| 文件大?。?/td> | 1834K |
| 代理商： | MB90F574/APFF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
MB90570 Series
18
The series without built-in step-down circuit have no oscillation setting time of step-down circuit, so outputs
should not become indeterminate. (MB90F574,MB90F574A,MB90574C)
12. Initialization
In the device, there are internal registers which are initialized only by a power-on reset. Turn on the power again
to initialize these registers.
13. Return from standby state
If the power-supply voltage goes below the standby RAM holding voltage in the standby state, the device may
fail to return from the standby state. In this case, reset the device via the external reset pin to return to the normal
state.
14. Precautions for Use of ’DIV A, Ri,’ and ’DIVW A, Ri’ Instructions
The signed multiplication-division instructions ’DIV A, Ri,’ and ’DIVW A, RWi’ should be used when the corre-
sponding bank registers (DTB, ADB, USB, SSB) are set to value ’00h.’ If the corresponding bank registers (DTB,
ADB, USB, SSB) are set to a value other than ’00h,’ then the remainder obtained after the execution of the
instruction will not be placed in the instruction operand register.
15. Precautions for Use of REALOS
Extended intelligent I/O service (EI2OS) cannot be used, when REALOS is used.
16. Caution on PLL Clock Mode
If the PLL clock mode is selected, the microcontroller attempt to be working with the self-oscillating circuit even
when there is no external oscillator or external clock input is stopped. Performance of this operation, however,
cannot be guaranteed.
Oscillation setting time *2
VCC (power-supply pin)
PONR (power-on reset) signal
RST (external asynchronous reset) signal
RST (internal reset) signal
Oscillation clock signal
KA (internal operating clock A) signal
KB (internal operating clock B) signal
PORT (port output) signal
Step-down circuit setting time *1
Period of indeterminate
*1: Step-down circuit setting time 217/oscillation clock frequency (oscillation clock frequency of 16 MHz: 8.19 ms)
*2: Oscillation setting time
218/oscillation clock frequency (oscillation clock frequency of 16 MHz: 16.38 ms)
Timing chart of indeterminate outputs from ports 0 and 1
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F997MBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90F997JBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90M407PF | MICROCONTROLLER, PQFP100 |
| MB90P214APF | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| MB90P634APF | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F583BPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583BPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583CAPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F591GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F594APFR-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。