- 您現在的位置：買賣IC網 > PDF目錄98010 > MB90F574/APFF (FUJITSU LTD) 16-BIT, FLASH, MICROCONTROLLER, PQFP120 PDF資料下載
參數資料
| 型號： | MB90F574/APFF |
| 廠商： | FUJITSU LTD |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, FLASH, MICROCONTROLLER, PQFP120 |
| 封裝： | PLASTIC, LQFP-120 |
| 文件頁數： | 29/120頁 |
| 文件大?。?/td> | 1834K |
| 代理商： | MB90F574/APFF |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁
MB90570 Series
16
s
s HANDLING DEVICES
1.
Preventing Latchup
CMOS ICs may cause latchup in the following situations:
When a voltage higher than Vcc or lower than Vss is applied to input or output pins.
When a voltage exceeding the rating is applied between Vcc and Vss.
When AVcc power is supplied prior to the Vcc voltage.
In turning on/turning off the analog power supply, make sure the analog power voltage (AVCC, AVRH, DVCC)and
analog input voltages not exceed the digital voltage (VCC).
2.
Treatment of unused pins
Leaving unused input pins open may result in misbehavior or latch up and possible permanent damage of the
device. Therefor they must be tied to VCC or Ground through resistors. In this case those resistors should be
more than 2 k
.
Unused bidirectional pins should be set to the output state and can be left open, or the input state with the above
described connection.
3.
Notes on Using External Clock
In using the external clock, drive X0 pin only and leave X1 pin unconnected.
4.
Unused Sub Clock Mode
If sub clock modes are not used, the oscillator should be connected to the X01A pin and X1A pin
5.
Power Supply Pins (VCC/VSS)
In products with multiple VCC or VSS pins, the pins of a same potential are internally connected in the device to
avoid abnormal operations including latch-up. However, connect the pins external power and ground lines to
lower the electro-magnetic emission level, to prevent abnormal operation of strobe signals caused by the rise
in the ground level, and to conform to the total current rating.
Make sure to connect VCC and VSS pins via lowest impedance to power lines.
Using external clock
MB90570 series
X0
X1
Open
相關PDF資料 |
PDF描述 |
|---|---|
| MB90F997MBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90F997JBSPMC | 16-BIT, FLASH, 32 MHz, MICROCONTROLLER, PQFP48 |
| MB90M407PF | MICROCONTROLLER, PQFP100 |
| MB90P214APF | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP80 |
| MB90P634APF | 16-BIT, OTPROM, 16 MHz, MICROCONTROLLER, PQFP100 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MB90F583BPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583BPMC-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F583CAPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F591GPFR-GE1 | 制造商:FUJITSU 功能描述: |
| MB90F594APFR-GE1 | 制造商:FUJITSU 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。