參數資料
型號： MB90F372PMT-G
元件分類： 微控制器/微處理器
英文描述： 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP144
封裝： 0.40 MM PITCH, PLASTIC, LQFP-144
文件頁數： 57/153頁
文件大?。?/td> 2503K
代理商： MB90F372PMT-G
MB90370 Series
15
■ HANDLING DEVICES
●
Be sure that the maximum rated voltage is not exceeded (latch-up prevention).
A latch-up may occur on a CMOS IC if a voltage higher than VCC or lower than VSS is applied
to an input or output pin other than medium-to-high voltage pins. A latch-up may also occur if
a voltage higher than the rating is applied between VCC and VSS. A latch-up causes a rapid
increase in the power supply current, which can result in thermal damage to an element.
Take utmost care that the maximum rated voltage is not exceeded.
When turning the power on or off to analog circuits, be sure that the analog supply voltages
(AVCC, CVCC, AVR, CVRH1, CVRH2 and CVRL) and analog input voltage do not exceed the
digital supply voltage (VCC).
●
Stabilize the supply voltages
Even within the operation guarantee range of the VCC supply voltage, a malfunction can be
caused if the supply voltage undergoes a rapid change. For voltage stabilization guidelines,
the VCC ripple fluctuations (P-P value) at commercial frequencies (50 to 60 Hz) should be
suppressed to "10%" or less of the reference VCC value. During a momentary change such
as when switching a supply voltage, voltage fluctuations should also be suppressed so that
the "transient fluctuation rate" is 0.1 V/ms or less.
●
Power-on
To prevent a malfunction in the built-in voltage drop circuit, secure "50
s (between 0.2 V and
1.8 V)" or more for the voltage rise time during power-on.
●
Treatment of unused input pins
An unused input pin may cause a malfunction if it is left open. Every unused input pin should
be pulled up or down.
●
Treatment of A/D converter, D/A converter and comparator power pin
When the A/D converter, D/A converter and comparator is not used, connect the pins as
follows: AVCC = CVCC = VCC, AVSS = AVR = CVSS = CVRL = CVRH1 = CVRH2 = VSS.
●
Notes on external clock
When an external clock is used, the oscillation stabilization wait time is required at power-on
reset or at cancellation of sub-clock mode or stop mode. As shown in diagram below, when
an external clock is used, connect only the X0 pin and leave the X1 pin open.
X0
X1
Open
MB90370 series
相關PDF資料
PDF描述
MB90F498GPFM 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
MB90497GPFM 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64
MB90F498GPMC 16-BIT, FLASH, 16 MHz, MICROCONTROLLER, PQFP64
MB90497GPMC 16-BIT, MROM, 16 MHz, MICROCONTROLLER, PQFP64
MB90F574/APFF 16-BIT, FLASH, MICROCONTROLLER, PQFP120
相關代理商/技術參數
參數描述
MB90F387PMCR-GSE1 制造商:FUJITSU 功能描述:
MB90F387PMT-GSE1 功能描述:IC MCU FLASH 64K ROM 48LQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - 微控制器， 系列:F²MC MB90385 產品培訓模塊:MCU Product Line Introduction XMEGA Introduction AVR XMEGA USB Connectivity 標準包裝:90 系列:AVR® XMEGA 核心處理器:AVR 芯體尺寸:8/16-位 速度:32MHz 連通性:I²C，IrDA，SPI，UART/USART 外圍設備:欠壓檢測/復位，DMA，POR，PWM，WDT 輸入/輸出數:50 程序存儲器容量:192KB（96K x 16） 程序存儲器類型:閃存 EEPROM 大小:4K x 8 RAM 容量:16K x 8 電壓 - 電源 (Vcc/Vdd):1.6 V ~ 3.6 V 數據轉換器:A/D 16x12b; D/A 2x12b 振蕩器型:內部 工作溫度:-40°C ~ 85°C 封裝/外殼:64-TQFP 包裝:托盤 配用:ATSTK600-RC14-ND - STK600 SOCKET/ADAPTER 64TQFPATSTK600-TQFP64-ND - STK600 SOCKET/ADAPTER 64-TQFPATAVRONEKIT-ND - KIT AVR/AVR32 DEBUGGER/PROGRMMRATAVRISP2-ND - PROGRAMMER AVR IN SYSTEM
MB90F387SPMCR-GE1 制造商:FUJITSU 功能描述:
MB90F387SPMCR-G-JNE1 制造商:FUJITSU 功能描述:
MB90F387SPMCRGSE1 制造商:FUJITSU 功能描述:Pb Free
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*