參數資料
型號： MAX9260GCB/V+T
廠商： Maxim Integrated Products
文件頁數： 35/51頁
文件大?。?/td> 0K
描述： IC DESERIALIZER GMSL 64TQFP
標準包裝： 750
系列： *
Gigabit Multimedia Serial Link with Spread
Spectrum and Full-Duplex Control Channel
MAX9259/MAX9260
40 _____________________________________________________________________________________
recognizes the UART sync pattern. For example, when
lowering the UART frequency from 1Mbps to 100kbps,
first send data at 333kbps and then at 100kbps to have
reduction ratios of 3 and 3.333, respectively.
LOCK Output Loopback
Connect the LOCK output to the INT input of the
MAX9260 to loopback LOCK to the MAX9259. The
interrupt output on the MAX9259 follows the transitions
at the LOCK output of the MAX9260. Reverse-channel
communication does not require an active forward link
to operate and accurately tracks the LOCK status of the
video link. LOCK asserts for video link only and not for
the configuration link.
MAX9260 GPIOs
The MAX9260 has two open-drain GPIOs available.
GPIO1OUT and GPIO0OUT (0x06 D3, D1) set the output
state of the GPIOs. The GPIO input buffers are always
enabled. The input states are stored in GPIO1 and
GPIO0 (0x06 D2, D0). Set GPIO1OUT/GPIO0OUT to 1
when using GPIO1/GPIO0 as an input.
Line-Fault Detection
The line-fault detector in the MAX9259 monitors for line
failures such as short to ground, short to power supply,
and open link for system fault diagnosis. Figure 3 shows
the required external resistor connections. LFLT = low
when a line fault is detected and LFLT = high when the
line returns to normal. The line-fault type is stored in
0x08 D[3:0] of the MAX9259. The fault-detector thresh-
old voltages are referenced to the MAX9259 ground.
Additional passive components set the DC level of the
cable (Figure 3). If the MAX9259 and MAX9260 grounds
are different, the link DC voltage during normal operation
can vary and cross one of the fault-detection thresholds.
For the fault-detection circuit, select the resistor’s power
rating to handle a short to the battery. Table 15 lists the
mapping for line-fault types.
Staggered Parallel Data Outputs
The MAX9260 staggers the parallel data outputs to
reduce EMI and noise. Staggering outputs also reduce
the power-supply transient requirements. By default,
the deserializer staggers outputs according to Table
16. Disable output staggering through the DISSTAG bit
(0x06 D7)
Choosing I2C/UART Pullup Resistors
Both I2C/UART open-drain lines require pullup resistors
to provide a logic-high level. There are tradeoffs between
power dissipation and speed, and a compromise must
be made in choosing pullup resistor values. Every device
connected to the bus introduces some capacitance even
when the device is not in operation. I2C specifies 300ns
rise times to go from low to high (30% to 70%) for fast
mode, which is defined for data rates up to 400kbps (see
the I2C specifications in the Electrical Characteristics
table for details). To meet the fast-mode rise-time
requirement, choose the pullup resistors so that rise time
tR = 0.85 x RPULLUP x CBUS < 300ns. The waveforms
are not recognized if the transition time becomes too
Table 15. MAX9259 Line-Fault Mapping
Table 16. Staggered Output Delay
REGISTER
ADDRESS
BITS
NAME
VALUE
LINE-FAULT TYPE
0x08
D[3:2]
LFNEG
00
Negative cable wire shorted to battery
01
Negative cable wire shorted to ground
10
Normal operation
11
Negative cable wire open
D[1:0]
LFPOS
00
Positive cable wire shorted to battery
01
Positive cable wire shorted to ground
10
Normal operation
11
Positive cable wire open
OUTPUT
OUTPUT DELAY RELATIVE
TO DOUT0 (ns)
DISSTAG = 0
DISSTAG = 1
DOUT0–DOUT5,
DOUT21, DOUT22
0
DOUT6–DOUT10,
DOUT23, DOUT24
0.5
0
DOUT11–DOUT15,
DOUT25, DOUT26
1
0
DOUT16–DOUT20,
DOUT27, DOUT28
1.5
0
PCLKOUT
0.75
0
相關PDF資料
PDF描述
MAX9259GCB/V+T IC SERIALIZER GMSL 64TQFP
MAX9217ETM+T IC SERIALIZER LVDS 48-TQFN
VI-B1X-IW-F1 CONVERTER MOD DC/DC 5.2V 100W
MAX9246GUM/V+T IC DESERIALIZER 21BIT 48TSSOP
MAX9244GUM/V+T IC DESERIALIZER 21BIT 48TSSOP
相關代理商/技術參數
參數描述
MAX9263EVKIT+ 制造商:Maxim Integrated Products 功能描述:GMSL SERIALIZER WITH HDCP - Boxed Product (Development Kits)
MAX9263GCB/V+ 功能描述:串行器/解串器 - Serdes GMSL Serializer w/HDCP Interface RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64
MAX9263GCB/V+T 功能描述:串行器/解串器 - Serdes GMSL Serializer w/HDCP Interface RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64
MAX9264EVKIT+ 制造商:Maxim Integrated Products 功能描述:GMSL DESERIALIZER WITH HDCP - Boxed Product (Development Kits)
MAX9264GCB/V+ 功能描述:串行器/解串器 - Serdes GMSL Deserializer w/HDCP Interface RoHS:否 制造商:Texas Instruments 類型:Deserializer 數據速率:1.485 Gbit/s 輸入類型:ECL/LVDS 輸出類型:LVCMOS 輸入端數量:1 輸出端數量:20 工作電源電壓:2.375 V to 2.625 V 工作溫度范圍:0 C to + 70 C 封裝 / 箱體:TQFP-64
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*