- 您現在的位置：買賣IC網 > PDF目錄69017 > M66596FP UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 PDF資料下載
參數資料
| 型號： | M66596FP |
| 元件分類： | 總線控制器 |
| 英文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP64 |
| 封裝： | 0.50 MM PITCH, LQFP-64 |
| 文件頁數： | 85/131頁 |
| 文件大小： | 1595K |
| 代理商： | M66596FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁
M66596FP/WG
rev .1.00
2006.3.14
page 57 of 127
3.1.8.3 Starting the internal clock supply (from the low-power sleep state to the normal operating state:
Auto clock supply function enabled)
Figure 3.7 shows a diagram of the timing at which the transition from the low-power sleep state to the normal
operating state takes place when the auto clock supply function is enabled (“ATCKM=1”). When the auto clock
supply function is enabled, the controller carries out register control, so after an interrupt is generated, the
transition to the normal operating state is completed simply by waiting for the amount of time that access is disabled.
No operation of the registers using the softwear is necessary.
In the Peripheral mode when operation has been resumed from the suspended state using the USB Bus Reset
signal, it is necessary to recover to the normal operating state within 3 ms after the data line change has been
detected so that the controller can begin the reset handshake protocol. When the auto clock supply function is
enabled, the controller waits automatically for oscillation to stabilize and then carries out clock supply control and
handles the reset handshake. Because there is a signal output time of 10 ms for the USB Bus Reset signal and of 20
ms for the Resume signal, the control program is provided with plenty of allowance to process the recovery to the
normal state.
The recovery sequence when the auto clock supply function is enabled is as shown below.
(1)
An interrupt is generated to recover from the low-power sleep state, and the INT_N pin is asserted.
(Or, the control program writes dummy data to the 0x7E address to cause the controller to recover.)
(2)
At the same time, the controller automatically enables the oscillation buffer. "XCKE=1(H/W)"
(3)
The softwear directs the system to wait until access is enabled. (A waiting time of at least 2.5 ms is
necessary.)
(4)
The controller automatically enables RCKE, PLLC, and SCKE.
(5)
The softwear resets the registers that have been in the held state before going into the low-power sleep state.
*1) In the Peripheral mode when the system has recovered from the low-power sleep state to the normal operating
state, the USB communication speed and the device state recovery settings have to be set in the STSRECOV bit
of the RECOVER register, and the USB address in the USBADDR bit of that register, for recovery to take place.
If the auto clock supply function has been enabled, however, the recovery settings for the above bits should be
entered after the DVSQ bit has been confirmed. This is because, if recovery has been made using the USB Bus
Reset signal, there is a possibility that the controller has initialized the device state and the USB address to the
default state, in which case rewriting the register values to the waiting state will cause erroneous operation.
The recovery settings are written to the RECOVER register using the procedure outlined below.
-
If “DVSQ=000”, recovery is made by a method other than the USB Bus Reset signal. The USB
communication speed, device state, and USB address should be returned to the state they were in prior to
shifting to the low-power sleep state, by writing to the RECOVER register.
-
If “DVSQ=001”, recovery is made using the USB Bus Reset signal. The recovery settings should not be
entered by writing to the RECOVER register.
Also, in the low-power sleep state, there are registers that are initialized by the controller. When recovery has
been made to the normal operating state, the initialized registers should be reset to match the user system.
XCKE(H/W )
RCKE(H/W)
PLLC(H/W)
SCKE(H/W )
(3)2.5ms (access disabled)
Low-power sleep
state recovery
PCUT(H/W)
INT_N
Event
CS_N
(1),(2)
(4)
Figure 3.7 Recovery control timing from the low-power sleep state with “ATCKM=1”
相關PDF資料 |
PDF描述 |
|---|---|
| M68HC11D3CFB1 | 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PQFP44 |
| M68HC711D0CFN | 8-BIT, 2 MHz, MICROCONTROLLER, PQCC44 |
| M68HC711D0CFB | 8-BIT, 2 MHz, MICROCONTROLLER, PQFP44 |
| M68HC711D3CFB1 | 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PQFP44 |
| M68HC711D3CP1 | 8-BIT, MROM, 1 MHz, MICROCONTROLLER, PDIP40 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M66596FP#RB0Z | 制造商:Renesas Electronics Corporation 功能描述:MCU - Trays 制造商:Renesas Electronics 功能描述:USB Device Controller 64-Pin LQFP Cut Tape 制造商:Renesas Electronics 功能描述:USB Device Controller 64-Pin LQFP Tray 制造商:Renesas 功能描述:USB Device Controller 64-Pin LQFP |
| M66596FPRB0Z | 制造商:Renesas Electronics Corporation 功能描述:USB2.0 Dual Function Controller,LQFP64 |
| M66596WG | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:ASSP (USB2.0 Dual Function Controller) |
| M66596WG#RB0Z | 制造商:Renesas Electronics 功能描述:Tray 制造商:Renesas 功能描述:0 |
| M6668 | 制造商:Tamura Corporation of America 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。