- 您現在的位置：買賣IC網 > PDF目錄383303 > M50LPW116N5T (意法半導體) 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory PDF資料下載
參數資料
| 型號： | M50LPW116N5T |
| 廠商： | 意法半導體 |
| 英文描述： | 16 Mbit 2Mb x8, Boot Block 3V Supply Low Pin Count Flash Memory |
| 中文描述： | 16兆位的2Mb × 8，啟動塊3V電源低引腳數快閃記憶體 |
| 文件頁數： | 6/36頁 |
| 文件大?。?/td> | 259K |
| 代理商： | M50LPW116N5T |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
M50LPW116
6/36
V
PP
Optional Supply Voltage.
The V
PP
Optional
Supply Voltage pin is used to select the Fast
Program (see the Quadruple Byte Program
Command description) and Fast Erase options of
the memory and to protect the memory. When
V
PP
< V
PPLK
Program and Erase operations
cannot be performed and an error is reported in
the Status Register if an attempt to change the
memory contents is made. When V
PP
= V
CC
Program and Erase operations take place as
normal. When V
PP
= V
PPH
Fast Program
operations (using the Quadruple Byte Program
command, 30h, from Table 11) and Fast Erase
operations are used. Any other voltage input to
V
PP
will result in undefined behavior and should
not be used.
V
PP
should not be set to V
PPH
for more than 80
hours during the life of the memory.
V
SS
Ground.
V
SS
is the reference for all the volt-
age measurements.
BUS OPERATIONS
The two interfaces have similar bus operations but
the signals and timings are completely different.
The Low Pin Count (LPC) Interface is the usual
interface and all of the functionality of the part is
available through this interface. Only a subset of
functions are available through the Address/
Address Multiplexed (A/A Mux) Interface.
Follow the section Low Pin Count (LPC) Bus
Operations below and the section Address/
Address Multiplexed (A/A Mux) Interface Bus
Operations below for a description of the bus
operations on each interface.
Low Pin Count (LPC) Bus Operations
The Low Pin Count (LPC) Interface consists of
four data signals (LAD0-LAD3), one control line
(LFRAME) and a clock (CLK). In addition
protection against accidental or malicious data
corruption can be achieved using two further
signals (TBL and WP). Finally two reset signals
(RP and INIT) are available to put the memory into
a known state.
The data signals, control signal and clock are
designed to be compatible with PCI electrical
specifications. The interface operates with clock
speeds up to 33MHz.
The following operations can be performed using
the appropriate bus cycles: Bus Read, Bus Write,
Standby, Reset and Block Protection.
Bus Read.
Bus Read operations read from the
memory cells, specific registers in the Command
Interface or Low Pin Count Registers. A valid Bus
Read operation starts when Input Communication
Frame, LFRAME, is Low, V
IL
, as Clock rises and
the correct Start cycle is on LAD0-LAD3. On the
following clock cycles the Host will send the Cycle
Type + Dir, Address and other control bits on
LAD0-LAD3. The memory responds by outputting
Sync data until the wait-states have elapsed
followed by Data0-Data3 and Data4-Data7.
See Table 6, and to Figure 4, for a description of
the Field definitions for each clock cycle of the
transfer. See Table 22, and Figure 9, for details on
the timings of the signals.
Bus Write.
Bus Write operations write to the
Command Interface or Low Pin Count Registers. A
valid Bus Write operation starts when Input
Communication Frame, LFRAME, is Low, V
IL
, as
Clock rises and the correct Start cycle is on LAD0-
Table 4. Absolute Maximum Ratings
(1)
Note: 1. Except for the rating "Operating Temperature Range", stresses above those listed in the Table "Absolute Maximum Ratings" may
cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions
above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating condi-
tions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant qual-
ity documents.
2.
Minimum Voltage may undershoot to –2V and for less than 20ns during transitions. Maximum Voltage may overshoot to V
CC
+2V
and for less than 20ns during transitions.
Symbol
Parameter
Value
Unit
T
A
Ambient Operating Temperature (Temperature Range Option 1)
0 to 70
°C
Ambient Operating Temperature (Temperature Range Option 5)
–20 to 85
°C
T
BIAS
Temperature Under Bias
–50 to 125
°C
T
STG
Storage Temperature
–65 to 150
°C
V
IO (2)
Input or Output Voltage
–0.6 to V
CC
+ 0.6
V
V
CC
Supply Voltage
–0.6 to 4
V
V
PP
Program Voltage
–0.6 to 13
V
相關PDF資料 |
PDF描述 |
|---|---|
| M51131L | 2 CHANNEL ELECTRONIC VOLUME BALANCE |
| M51354AP | TV IF SYSTEM |
| M51391ASP | PAL/NTSC VIDEO CHROMA DEFLECTION |
| M52063SP | NTSC/QUASI PAL TRANSCODER |
| M5224FP | QUAD SINGLE POWER SUPPLY OPERATIONAL AMPLIFIERS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M50LPW116N5TG | 功能描述:閃存 16 MBIT 3V SUPPLY RoHS:否 制造商:ON Semiconductor 數據總線寬度:1 bit 存儲類型:Flash 存儲容量:2 MB 結構:256 K x 8 定時類型: 接口類型:SPI 訪問時間: 電源電壓-最大:3.6 V 電源電壓-最小:2.3 V 最大工作電流:15 mA 工作溫度:- 40 C to + 85 C 安裝風格:SMD/SMT 封裝 / 箱體: 封裝:Reel |
| M50M40-6-0M | 制造商:Jacob 功能描述: |
| M50-MAGNET | 制造商:Brady Corporation 功能描述:PRINTER HOLDING MAGNET ACCESSORY, BMP50 SERIES; Accessory Type:Printer-Holding Magnetic Attachment; Features:Securely Holds BMP51 Printer & Adheres it to Metal Surfaces for Convenient 1-Hand Use ;RoHS Compliant: Yes |
| M50MPK | 制造商:Mallory Sonalert Products Inc 功能描述:Res Wirewound POT 50K Ohm 10% 4W 1(Elec)/1(Mech)Turn 6.35mm (33.34 X 39.67 X 50.04mm) Solder Lug Panel Mount |
| M50P03HDL | 制造商:Motorola Inc 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。