- 您現在的位置：買賣IC網 > PDF目錄67763 > M38049FFLWG 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 PDF資料下載
參數資料
| 型號： | M38049FFLWG |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PBGA64 |
| 封裝： | 6 X 6 MM, 0.65 MM PITCH, PLASTIC, LGA-64 |
| 文件頁數： | 9/129頁 |
| 文件大?。?/td> | 1721K |
| 代理商： | M38049FFLWG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁
Rev.1.00
Oct 27, 2008
Page 106 of 128
REJ03B0266-0100
3804 Group (Spec.L)
NOTES
NOTES ON PROGRAMMING
1. Processor Status Register
(1) Initializing of processor status register
Flags which affect program execution must be initialized after a reset.
In particular, it is essential to initialize the T and D flags because
they have an important effect on calculations.
<Reason>
After a reset, the contents of the processor status register (PS) are
undefined except for the I flag which is “1”.
Fig. 101 Initialization of processor status register
(2) How to reference the processor status register
To reference the contents of the processor status register (PS),
execute the PHP instruction once then read the contents of (S+1).
If necessary, execute the PLP instruction to return the PS to its
original status.
Fig. 102 Stack memory contents after PHP instruction
execution
2. Decimal calculations
(1) Execution of decimal calculations
The ADC and SBC are the only instructions which will yield
proper decimal notation, set the decimal mode flag (D) to “1”
with the SED instruction. After executing the ADC or SBC
instruction, execute another instruction before executing the
SEC, CLC, or CLD instruction.
(2) Notes on status flag in decimal mode
When decimal mode is selected, the values of three of the flags in
the status register (the N, V, and Z flags) are invalid after a ADC
or SBC instruction is executed.
The carry flag (C) is set to “1” if a carry is generated as a result of the
calculation, or is cleared to “0” if a borrow is generated. To
determine whether a calculation has generated a carry, the C flag
must be initialized to “0” before each calculation. To check for a
borrow, the C flag must be initialized to “1” before each calculation.
Fig. 103 Execution of decimal calculations
3. JMP instruction
When using the JMP instruction in indirect addressing mode, do
not specify the last address on a page as an indirect address.
4. Multiplication and Division Instructions
The index X mode (T) and the decimal mode (D) flags do not
affect the MUL and DIV instruction.
The execution of these instructions does not change the
contents of the processor status register.
5. Ports
The contents of the port direction registers cannot be read. The
following cannot be used:
The data transfer instruction (LDA, etc.)
The operation instruction when the index X mode flag (T) is “1”
The instruction with the addressing mode which uses the value
of a direction register as an index
The bit-test instruction (BBC or BBS, etc.) to a direction
register
The read-modify-write instructions (ROR, CLB, or SEB, etc.)
to a direction register.
Use instructions such as LDM and STA, etc., to set the port
direction registers.
6. Instruction Execution Timing
The instruction execution time can be obtained by multiplying
the frequency of the internal clock
φ by the number of cycles
mentioned in the 740 Family Software Manual.
The frequency of the internal clock
φ is the twice the XIN cycle in
high-speed mode, 8 times the XIN cycle in middle-speed mode,
and the twice the XCIN in low-speed mode.
Reset
Initializing of flags
Main program
Stored PS
(S)
(S) + 1
Set D flag to “1”
ADC or SBC instruction
NOP instruction
SEC, CLC, or CLD instruction
相關PDF資料 |
PDF描述 |
|---|---|
| M38049FFLHP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PQFP64 |
| M38049FFLSP | 8-BIT, FLASH, 16.8 MHz, MICROCONTROLLER, PDIP64 |
| M38112E4SS | 8-BIT, UVPROM, 4.19 MHz, MICROCONTROLLER, CDIP64 |
| M38112E4-XXXFP | 8-BIT, OTPROM, 4.19 MHz, MICROCONTROLLER, PQFP64 |
| M38112E4-XXXSP | 8-BIT, OTPROM, 4.19 MHz, MICROCONTROLLER, PDIP64 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M38049RLSS | 功能描述:DEV EMULATOR CHIP RAM 2KB 64SDIP RoHS:否 類別:編程器，開發系統 >> 內電路編程器、仿真器以及調試器 系列:- 產品變化通告:Development Systems Discontinuation 19/Jul/2010 標準包裝:1 系列:* 類型:* 適用于相關產品:* 所含物品:* |
| M3806 | 功能描述:電纜固定件和配件 LTSCG 625 BLACK RoHS:否 制造商:Heyco 類型:Cable Grips, Liquid Tight 材料:Nylon 顏色:Black 安裝方法:Cable 最大光束直徑:11.4 mm 抗拉強度: |
| M3806 BK001 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 1000' |
| M3806 BK002 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 500' |
| M3806 BK005 | 制造商:Alpha Wire Company 功能描述:CBL 8COND 18AWG BLK 100' |
發布緊急采購，3分鐘左右您將得到回復。