- 您現在的位置：買賣IC網 > PDF目錄45038 > M37905M8C-XXXSP 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64 PDF資料下載
參數資料
| 型號： | M37905M8C-XXXSP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64 |
| 封裝： | 0.750 INCH, 1.78 MM PITCH, PLASTIC, SDIP-64 |
| 文件頁數： | 19/103頁 |
| 文件大?。?/td> | 1402K |
| 代理商： | M37905M8C-XXXSP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁
21
M37905M4C-XXXFP, M37905M4C-XXXSP
M37905M6C-XXXFP, M37905M6C-XXXSP
M37905M8C-XXXFP, M37905M8C-XXXSP
PRELIMINAR
Y
Notice:
This
is not
a final
specification.
Some
parametric
limits
are
subject
to change.
16-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
INTERRUPTS
Table 3 shows the interrupt sources and the corresponding interrupt
vector addresses. Reset is also handled as an interrupt source in
this section, too.
DBC and BRK instruction are interrupts used only for debugging.
Therefore, do not use these interrupts.
Interrupts other than reset, watchdog timer, zero divide, and address
matching detection all have interrupt control registers. Table 4 shows
the addresses of the interrupt control registers and Figure 13 shows
the bit configuration of the interrupt control register.
The interrupt request bit is automatically cleared by the hardware
during reset or when processing an interrupt. Also, interrupt request
bits except for that of a watchdog timer interrupt can be cleared by
software.
An INTi (i = 0 to 7) interrupt request is generated by an external in-
put.
INTi is an external interrupt; whether to cause an interrupt at the in-
put level (level sense) or at the edge (edge sense) can be selected
with the level/edge select bit. Furthermore, the polarity of the inter-
rupt input can be selected with the polarity select bit.
When using the following pins as external interrupt input pins, be
sure to clear the direction registers of the corresponding multiplexed
ports to “0”: pins P51/INT1, P52/INT2, P53/INT3, P55/INT5, P56/INT6,
and P57/INT7.
When the external interrupt input read register (address 9516), which
is shown in Figure 12, is read out, the status of pins INT0 through
INT7 can directly be read.
Timer and UART interrupts are described in the respective section.
The priority of interrupts when multiple interrupt requests are caused
simultaneously is partially fixed by hardware, but, it can also be ad-
justed by software as shown in Figure 14.
The hardware priority is fixed as the following:
reset > watchdog timer > other interrupts
Interrupts
UART2 transmit
UART2 receive
Timer A9
Timer A8
Timer A7
Timer A6
Timer A5
INT7 external interrupt
INT6 external interrupt
INT5 external interrupt
Address matching detection interrupt
INT4 external interrupt
INT3 external interrupt
A-D conversion
UART1 transmit
UART1 receive
UART0 transmit
UART0 receive
Timer B2
Timer B1
Timer B0
Timer A4
Timer A3
Timer A2
Timer A1
Timer A0
INT2 external interrupt
INT1 external interrupt
INT0 external interrupt
Watchdog timer
DBC (Do not select.)
Break instruction (Do not select.)
Zero divide
Reset
Table 3. Interrupt sources and interrupt vector addresses
Vector addresses
00FFB416
00FFB516
00FFB616
00FFB716
00FFB816
00FFB916
00FFBA16
00FFBB16
00FFBC16
00FFBD16
00FFBE16
00FFBF16
00FFC016
00FFC116
00FFC216
00FFC316
00FFC416
00FFC516
00FFC616
00FFC716
00FFCA16
00FFCB16
00FFD016
00FFD116
00FFD216
00FFD316
00FFD416
00FFD516
00FFD616
00FFD716
00FFD816
00FFD916
00FFDA16
00FFDB16
00FFDC16
00FFDD16
00FFDE16
00FFDF16
00FFE016
00FFE116
00FFE216
00FFE316
00FFE416
00FFE516
00FFE616
00FFE716
00FFE816
00FFE916
00FFEA16
00FFEB16
00FFEC16
00FFED16
00FFEE16
00FFEF16
00FFF016
00FFF116
00FFF216
00FFF316
00FFF616
00FFF716
00FFF816
00FFF916
00FFFA16
00FFFB16
00FFFC16
00FFFD16
00FFFE16
00FFFF16
Fig. 12 Bit configuration of external interrupt input read register
76543210
INT0 read bit
INT1 read bit
INT2 read bit
INT3 read bit
INT4 read bit
INT5 read bit
INT6 read bit
INT7 read bit
External interrupt input read register
Address
9516
相關PDF資料 |
PDF描述 |
|---|---|
| M37905M8C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PQFP64 |
| M37905M6C-XXXSP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDIP64 |
| M37906M4H-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906M6C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDSO42 |
| M37906M8C-XXXFP | 16-BIT, MROM, 20 MHz, MICROCONTROLLER, PDSO42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M37905T-PRB | 功能描述:DEV POD PROBE FOR M37900T2-RPD-E RoHS:否 類別:編程器，開發系統 >> 配件 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program RoHS指令信息:IButton RoHS Compliance Plan 標準包裝:1 系列:- 附件類型:USB 至 1-Wire? RJ11 適配器 適用于相關產品:1-Wire? 設備 產品目錄頁面:1429 (CN2011-ZH PDF) |
| M37906F8CFP | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906F8CFP-T4 | 制造商:Renesas Electronics Corporation 功能描述:FLSH 16-BIT |
| M37906F8CSP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
| M37906M4C-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:16-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。