參數資料
型號： M37641M8-XXXHP
廠商： Mitsubishi Electric Corporation
英文描述： SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
中文描述： 單芯片8位CMOS微機
文件頁數： 119/149頁
文件大?。?/td> 1997K
代理商： M37641M8-XXXHP
119
7641 Group
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
MITSUBISHI MICROCOMPUTERS
PRELIMINARY
Notice: This is not a final specification.
change.
Some parametric limits are subject to
G
Erase All Blocks Command (20
16
/20
16
)
By writing the command code
“
20
16
”
in the first bus cycle and the
confirmation command code
“
20
16
”
in the second bus cycle that
follows, the erase all blocks (erase and erase verify) operation
starts.
Whether the erase all blocks command is terminated can be con-
firmed by reading the status register or the RY/BY signal status .
When the erase all blocks operation starts, the read status regis-
ter mode is entered automatically and the contents of the status
register can be read out at the data I/O pins (DB
0
to DB
7
). The
status register bit 7 (SR7) is set to
“
0
”
at the same time the erase
operation starts and is returned to
“
1
”
upon completion of the
erase operation. In this case, the read status register mode re-
mains active until another command is written.
The RY/BY pin is
“
L
”
during erase operation and
“
H
”
when the
erase operation is completed as is the status register bit 7 (SR7).
At erase all blocks end, erase results can be checked by reading
the status register. For details, refer to the section where the sta-
tus register is detailed.
G
Block Erase Command (20
16
/D0
16
)
By writing the command code
“
20
16
”
in the first bus cycle and the
confirmation command code
“
D0
16
”
in the second bus cycle that
follows to the block address of a flash memory block, the block
erase (erase and erase verify) operation starts.
Whether the block erase operation is completed can be confirmed
by reading the status register or the RY/BY pin state. When the
block erase operation starts, the read status register mode is en-
tered automatically and the contents of the status register can be
read out at the data I/O pins (DB
0
to DB
7
). The status register bit
7 (SR7) is set to
“
0
”
at the same time the block erase operation
starts and is returned to
“
1
”
upon completion of the block erase
operation. In this case, the read status register mode remains ac-
tive until the read array command (FF
16
) is written.
The RY/BY pin is
“
L
”
during block erase operation and
“
H
”
when
the block erase operation is completed as is the status register bit
7 (SR7).
At block erase operation end, erase results can be checked by
reading the status register. For details, refer to the section where
the status register is detailed.
Figure 100 shows the erase flowchart.
Fig. 100 Erase flowchart
W
r
i
t
e
2
0
1
6
2
o
0
1
c
k
6
/
a
D
d
0
1
d
6
e
B
l
r
s
s
Erase completed
(Write read command FF
16
)
NO
YES
S
t
a
r
t
W
r
i
t
e
SR5 = 0
Erase error
Y
E
S
NO
2
D
0
1
0
1
6
:
6
:
E
B
r
l
a
o
s
c
e
k
a
e
l
r
l
a
b
s
l
o
e
c
k
s
SR 7 = 1
or
RY/BY = 1
Status register
read
相關PDF資料
PDF描述
M37702M2-127FP SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
M37702S1AFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702S1BFP Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702M2A Single Chip 16 Bits CMOS Microcomputer(16位單片機)
M37702M2B Single Chip 16 Bits CMOS Microcomputer(16位單片機)
相關代理商/技術參數
參數描述
M376420RS 制造商:OKI 功能描述:3764-20 NOTES
M3764-20RS 制造商:OKI 功能描述:3764-20 NOTES 制造商: 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP 制造商:OK International 功能描述:Dynamic RAM, Page Mode, 64K x 1, 16 Pin, Plastic, DIP
M3-7643A-S 制造商:Harris Corporation 功能描述:
M37643F8E8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
M37643F8M8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*