- 您現在的位置：買賣IC網 > PDF目錄69011 > M34551E8FP 4-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP48 PDF資料下載
參數資料
| 型號： | M34551E8FP |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | 4-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP48 |
| 封裝： | 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48 |
| 文件頁數： | 99/155頁 |
| 文件大小： | 1329K |
| 代理商： | M34551E8FP |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁當前第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁
HARDWARE
1-36
4551 Group User’s Manual
(5) Identification of the start condition
Warm start or cold start can be identified by examining the
state of the power down flag (P) with the SNZP instruction.
The warm start condition (timer 2 or external wakeup signal)
can be identified by examining the state of T2F flag.
Fig. 34 Set source and clear source of the P flag
q Set source
POF or POF2 instruction executed
q Clear source
Reset input
S
R
Q
Powerdown flag P
POF instruction
or
POF2 instruction
Reset input
Software start
P = “1”
T2F = “1”
?
No
Yes
Return by external
wakeup signal
Return by timer 2
underflow
Cold start
No
Fig. 35 Start condition identified example using the SNZP instruction
(6) Return signal
An external wakeup signal or timer 2 interrupt request flag is
used to return from the clock operating mode.
An external wakeup signal is used to return from the RAM
back-up mode because the oscillation is stopped. Table 16
shows the return condition for each return source.
(7) Port P1 control register
q Pull-up control register PU0
Register PU0 controls the ON/OFF of the port P1 pull-up
transistor and the ON/OFF of the key-on wakeup function.
Set the contents of this register through register A with
the TPU0A instruction. In addition, the TAPU0 instruction
can be used to transfer the contents of register PU0 to
register A.
Table 16 Return source and return condition
Remarks
Port P0 shares the falling edge detection circuit with port P1. The key-on
wakeup function of port P0 is always valid. The only key-on wakeup
function of the port P1 bit of which the pull-up transistor is turned on is
valid. Set all the port using the key-on wakeup function to “H” level before
going into the power down state.
The timer 2 interrupt request flag (T2F) can be used only when system
returns from the clock operating mode (POF instruction execution).
However, if the POF and POF2 instructions are executed while the T2F =
“1”, its operation is recognized as the return condition and system returns
from the clock operating mode.
Return condition
Returns by an external falling
edge input (“H”
→“L”).
Returns by timer 2 underflow and
setting T2F to “1.”
Return source
Ports P0, P1
Timer 2 interrupt
request flag
External
wakeup
signal
Note: P1 pin has the pull-up transistor which can be turned on/off by software.
Table 17 Pull-up control register
Pull-up transistor OFF, no key-on wakeup
Pull-up transistor ON, key-on wakeup
Pull-up transistor OFF, no key-on wakeup
Pull-up transistor ON, key-on wakeup
Pull-up transistor OFF, no key-on wakeup
Pull-up transistor ON, key-on wakeup
Pull-up transistor OFF, no key-on wakeup
Pull-up transistor ON, key-on wakeup
Port P13 pull-up transistor
control bit
Port P12 pull-up transistor
control bit
Port P11 pull-up transistor
control bit
Port P10 pull-up transistor
control bit
0
1
0
1
0
1
0
1
at reset : 00002
at power down : state retained
Pull-up control register PU0
R/W
PU03
PU02
PU01
PU00
Note: “R” represents read enabled, and “W” represents write enabled.
FUNCTIONAL BLOCK OPERATIONS
相關PDF資料 |
PDF描述 |
|---|---|
| M34551M4-XXXFP | 4-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP48 |
| M34552G8FP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34552M8H-XXXFP | 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34552G8HFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48 |
| M34556G8HFP | 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M34551E8-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551M4 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34551M4-XXXFP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER |
| M34551M8 | 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER |
| M34552G8FP | 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER |
發布緊急采購，3分鐘左右您將得到回復。