參數資料
型號： M34551E8FP
元件分類： 微控制器/微處理器
英文描述： 4-BIT, OTPROM, 8 MHz, MICROCONTROLLER, PQFP48
封裝： 7 X 10 MM, 0.65 MM PITCH, PLASTIC, QFP-48
文件頁數： 104/155頁
文件大小： 1329K
代理商： M34551E8FP
HARDWARE
1-40
4551 Group User’s Manual
LIST OF PRECAUTIONS
Noise and latch-up prevention
Connect a capacitor on the following condition to prevent noise
and latch-up;
connect a bypass capacitor (approx. 0.1
F) between pins
VDD and VSS at the shortest distance,
equalize its wiring in width and length, and
use the thickest wire.
In the built-in PROM version, CNVSS pin is also used as VPP
pin. Accordingly, when using this pin, connect this pin to VSS
through a resistor about 5 k
(connect this resistor to CNVSS/
VPP pin as close as possible).
Prescaler
Stop the prescaler operation to change its frequency dividing
ratio.
Count source
Stop timer 1 or timer LC counting to change its count source.
When timer 2 count source changes from f(XCIN) to ORCLK
(W23 = “0”
→ W23 = “1”), the count value of timer 2 is initialized.
However, when timer 2 count source changes from ORCLK to
f(XCIN) (W23 = “1”
→ W23 = “0”) or the same count source is
set again (W23 = “0”
→ W23 = “0” or W23 = “1” → W23 = “1”),
the count value of timer 2 is not initialized.
Timer 2
Timer 2 has the watchdog timer function (WDT). When timer 2
is used as the WDT, note that the processing to initialize the
count value and the execution of the WRST instruction.
Reading the count value
Stop the prescaler and then execute the TAB1 instruction to
read timer 1 data.
Writing to reload register R1
Write the data to reload register R1 while timer 1 is operating,
avoid a timing when timer 1 underflows.
Notes when using the carrier wave output auto-control function
Execute the STCR instruction after setting the timer 1 and
register C2 in order to start the carrier generating circuit
operation.
Stop the timer 1 (W20=“0”) after stopping the carrier
generating circuit (SPCR instruction executed) while the
carrier wave output is disabled in order to stop the carrier
wave output auto-control operation.
If the carrier wave output auto-control function is invalidated
(C20=“0”) while the carrier wave output is auto-controlled,
the output of port CARR retains the state when the auto-
control is invalidated regardless of timer 1 underflow. This
state is released by timer 1 stop (W20=“0”).
When the carrier wave output auto-control function is
validated (C20=“1”) again after it is invalidated (C20=“0”),
the auto-control of carrier wave output is started again when
the next timer 1 underflow occurs. However, when the carrier
wave output auto-control bit is changed during timer 1
underflow, the error-operation may occur.
Use the carrier wave or the carrier wave divided by 2 as the
timer 1 count source when the carrier wave output auto-
control function is selected.
If the ORCLK is used as the count source, a hazard may
occur in port CARR output because ORCLK is not
synchronized with the carrier wave.
When “no carrier wave” is selected with register C1
((C13C12C11C10) = (0101), (1101)), the enable/disable of
the carrier wave output cannot be controlled by the carrier
wave output auto-control function.
D5/INT pin
When the interrupt valid waveform of D5/INT pin is changed
with the bit 2 of register I1 in software, be careful about the
following notes.
Clear the bit 0 of register V1 to “0” and then change the
interrupt valid waveform of D5/INT pin with the bit 2 of register
I1 (refer to Figure 40).
Clear the bit 2 of register I1 to “0” and execute the SNZ0
instruction to clear the EXF0 flag after executing at least
one instruction (refer to Figure 40). Depending on the input
state of the D5/INT pin, the external 0 interrupt request flag
(EXF0) may be set to “1” when the interrupt valid waveform
is changed.
LA
4
; (!!!02)
TV1A
; The SNZ0 instruction is valid
LA
4
TI1A
; Change of the interrupt valid waveform
NOP
SNZ0
;The SNZ0 instruction is executed
NOP
! : this bit is not related to the setting of INT.
...
One Time PROM version
The operating power voltage of the One Time PROM version
is within the range of 2.5 V to 5.5 V.
Multifunction
Note that the port D5 output function can be used even when
INT function is selected.
Power down instruction (POF instruction, POF2 instruction)
Execute the POF or POF2 instruction immediately after
executing the EPOF instruction to enter the power down state.
Note that system cannot enter the power down state when
executing only the POF or POF2 instruction.
Be sure to disable interrupts by executing the DI instruction
before executing the EPOF instrcution.
Program counter
Make sure that the PCH does not specify after the last page of
the built-in ROM.
Fig. 40 External 0 interrupt program example
12
11
LIST OF PRECAUTIONS
相關PDF資料
PDF描述
M34551M4-XXXFP 4-BIT, MROM, 8 MHz, MICROCONTROLLER, PQFP48
M34552G8FP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48
M34552M8H-XXXFP 4-BIT, MROM, 6 MHz, MICROCONTROLLER, PQFP48
M34552G8HFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PQFP48
M34556G8HFP 4-BIT, OTPROM, 6 MHz, MICROCONTROLLER, PDSO42
相關代理商/技術參數
參數描述
M34551E8-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER
M34551M4 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER
M34551M4-XXXFP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for INFRARED REMOTE CONTROL TRANSMITTER
M34551M8 制造商:MITSUBISHI 制造商全稱:Mitsubishi Electric Semiconductor 功能描述:4-BIT SINGLE-CHIP MICROCOMPUTER
M34552G8FP 制造商:RENESAS 制造商全稱:Renesas Technology Corp 功能描述:SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*