參數資料
型號: M25PE10-VMN6TP
廠商: 意法半導體
元件分類: DRAM
英文描述: 4 Mbit Uniform Sector, Serial Flash Memory
中文描述: 4兆位統一部門,串行閃存
文件頁數: 24/37頁
文件大?。?/td> 198K
代理商: M25PE10-VMN6TP
M25PE10, M25PE20
24/37
POWER-UP AND POWER-DOWN
At Power-up and Power-down, the device must
not be selected (that is Chip Select (S) must follow
the voltage applied on V
CC
) until V
CC
reaches the
correct value:
V
CC
(min) at Power-up, and then for a further
delay of t
VSL
V
SS
at Power-down
Usually a simple pull-up resistor on Chip Select (S)
can be used to ensure safe and proper Power-up
and Power-down.
To avoid data corruption and inadvertent write op-
erations during power up, a Power On Reset
(POR) circuit is included. The logic inside the de-
vice is held reset while V
CC
is less than the Power
On Reset (POR) threshold value, V
WI
– all opera-
tions are disabled, and the device does not re-
spond to any instruction.
Moreover, the device ignores all Write Enable
(WREN), Page Write (PW), Page Program (PP),
Page Erase (PE) and Sector Erase (SE) instruc-
tions until a time delay of t
PUW
has elapsed after
the moment that V
CC
rises above the V
WI
thresh-
old. However, the correct operation of the device
is not guaranteed if, by this time, V
CC
is still below
V
CC
(min). No Write, Program or Erase instructions
should be sent until the later of:
t
PUW
after V
CC
passed the V
WI
threshold
t
VSL
after V
CC
passed the V
CC
(min) level
These values are specified in
Table 7.
If the delay, t
VSL
, has elapsed, after V
CC
has risen
above V
CC
(min), the device can be selected for
READ instructions even if the t
PUW
delay is not yet
fully elapsed.
As an extra protection, the Reset (Reset) signal
could be driven Low for the whole duration of the
Power-up and Power-down phases.
At Power-up, the device is in the following state:
The device is in the Standby Power mode (not
the Deep Power-down mode).
The Write Enable Latch (WEL) bit is reset.
Normal precautions must be taken for supply rail
decoupling, to stabilize the VCC supply. Each de-
vice in a system should have the VCC rail decou-
pled by a suitable capacitor close to the package
pins. (Generally, this capacitor is of the order of
0.1 μF).
At Power-down, when VCC drops from the operat-
ing voltage, to below the Power On Reset (POR)
threshold voltage, VWI, all operations are disabled
and the device does not respond to any instruc-
tion. (The designer needs to be aware that if a
Power-down occurs while a Write, Program or
Erase cycle is in progress, some data corruption
can result.)
Figure 20. Power-up Timing
VCC
AI04009C
VCC(min)
VWI
Reset State
of the
Device
Chip Selection Not Allowed
Program, Erase and Write Commands are Rejected by the Device
tVSL
tPUW
time
Read Access allowed
Device fully
accessible
VCC(max)
相關PDF資料
PDF描述
M25PE20 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMP6G 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMP6P 4 Mbit Uniform Sector, Serial Flash Memory
M25PE16-VMP6TG 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M25PE10-VMN6TPBA 制造商:Micron Technology Inc 功能描述:SERIAL NOR 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 3V/3.3V 1Mbit 128K x 8bit 8ns T/R 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel
M25PE10-VMN6TPBA TR 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8SO
M25PE10-VMP6G 制造商:Micron Technology Inc 功能描述:FLASH SERL-SPI 3.3V 1MBIT 128KX8 8NS 8PIN VDFPN EP - Trays 制造商:Micron Technology Inc 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN
M25PE10-VMP6P 制造商:NUMONYX 制造商全稱:Numonyx B.V 功能描述:1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
M25PE10-VMP6TG 功能描述:IC FLASH 1MBIT 75MHZ 8VFQFPN RoHS:是 類別:集成電路 (IC) >> 存儲器 系列:Forté™ 產品變化通告:Product Discontinuation 26/Apr/2010 標準包裝:136 系列:- 格式 - 存儲器:RAM 存儲器類型:SRAM - 同步,DDR II 存儲容量:18M(1M x 18) 速度:200MHz 接口:并聯 電源電壓:1.7 V ~ 1.9 V 工作溫度:0°C ~ 70°C 封裝/外殼:165-TBGA 供應商設備封裝:165-CABGA(13x15) 包裝:托盤 其它名稱:71P71804S200BQ