- 您現在的位置：買賣IC網 > PDF目錄377802 > M25P40 (意法半導體) 4 Mbit Uniform Sector, Serial Flash Memory PDF資料下載
參數資料
| 型號： | M25P40 |
| 廠商： | 意法半導體 |
| 元件分類： | DRAM |
| 英文描述： | 4 Mbit Uniform Sector, Serial Flash Memory |
| 中文描述： | 4兆位統一部門，串行閃存 |
| 文件頁數： | 8/51頁 |
| 文件大?。?/td> | 398K |
| 代理商： | M25P40 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁
Signal description
M25P40
8/51
2
Signal description
2.1
Serial Data Output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the
falling edge of Serial Clock (C).
2.2
Serial Data Input (D)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be programmed. Values are latched on the rising edge of Serial
Clock (C).
2.3
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at Serial Data Input (D) are latched on the rising edge of Serial Clock (C). Data on
Serial Data Output (Q) changes after the falling edge of Serial Clock (C).
2.4
Chip Select (S)
When this input signal is High, the device is deselected and Serial Data Output (Q) is at high
impedance. Unless an internal Program, Erase or Write Status Register cycle is in progress,
the device will be in the Standby Power mode (this is not the Deep Power-down mode).
Driving Chip Select (S) Low selects the device, placing it in the Active Power mode.
After Power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
2.5
Hold (HOLD)
The Hold (HOLD) signal is used to pause any serial communications with the device without
deselecting the device.
During the Hold condition, the Serial Data Output (Q) is high impedance, and Serial Data
Input (D) and Serial Clock (C) are Don’t Care.
To start the Hold condition, the device must be selected, with Chip Select (S) driven Low.
2.6
Write Protect (W)
The main purpose of this input signal is to freeze the size of the area of memory that is
protected against program or erase instructions (as specified by the values in the BP2, BP1
and BP0 bits of the Status Register).
相關PDF資料 |
PDF描述 |
|---|---|
| M25PE10-VMN6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE20-VMP6TP | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMN6P | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMP6G | 4 Mbit Uniform Sector, Serial Flash Memory |
| M25PE10-VMP6P | 4 Mbit Uniform Sector, Serial Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| M25P40_07 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:4 Mbit, low voltage, serial Flash memory with 50 MHz SPI bus interface |
| M25P40_12 | 制造商:MICRON 制造商全稱:Micron Technology 功能描述:Micron M25P40 Serial Flash Embedded Memory |
| M25P40-VMB3TPB | 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE - Tape and Reel |
| M25P40-VMB3TPB TR | 制造商:Micron Technology Inc 功能描述:IC FLASH 4MBIT 75MHZ 8UFDFPN |
| M25P40-VMB6TPB | 制造商:Micron Technology Inc 功能描述:4MBIT SPI NOR FLASH 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Cut TR (SOS) 制造商:Micron Technology Inc 功能描述:AUTOMOTIVE FLASH - Tape and Reel 制造商:Micron Technology Inc 功能描述:NOR Flash Serial-SPI 2.5V/3.3V 4Mbit 512K x 8bit 8ns 8-Pin UFDFPN EP T/R |
發布緊急采購，3分鐘左右您將得到回復。