參數資料
型號： M24C32
廠商： 意法半導體
英文描述： 32K Serial IIC Bus EEPROM(32K串行IIC總線EEPROM)
中文描述： 32K的串行IIC總線的EEPROM（32K的串行總線EEPROM的國際進口許可證）
文件頁數： 19/35頁
文件大?。?/td> 330K
代理商： M24C32
M24128, M24C64, M24C32
Device operation
19/35
4.10
Read operations
Read operations are performed independently of the state of the Write Control (WC) signal.
After the successful completion of a Read operation, the device’s internal address counter is
incremented by one, to point to the next byte address.
4.11
Random Address Read
A dummy Write is first performed to load the address into this address counter (as shown in
Figure 10
) but
without
sending a Stop condition. Then, the bus master sends another Start
condition, and repeats the Device Select Code, with the Read/Write bit (RW) set to 1. The
device acknowledges this, and outputs the contents of the addressed byte. The bus master
must
not
acknowledge the byte, and terminates the transfer with a Stop condition.
4.12
Current Address Read
For the Current Address Read operation, following a Start condition, the bus master only
sends a Device Select Code with the Read/Write bit (RW) set to 1. The device
acknowledges this, and outputs the byte addressed by the internal address counter. The
counter is then incremented. The bus master terminates the transfer with a Stop condition,
as shown in
Figure 10
,
without
acknowledging the Byte.
4.13
Sequential Read
This operation can be used after a Current Address Read or a Random Address Read. The
bus master
does
acknowledge the data byte output, and sends additional clock pulses so
that the device continues to output the next byte in sequence. To terminate the stream of
bytes, the bus master must
not
acknowledge the last byte, and
must
generate a Stop
condition, as shown in
Figure 10
.
The output data comes from consecutive addresses, with the internal address counter
automatically incremented after each byte output. After the last memory address, the
address counter ‘rolls-over’, and the device continues to output data from memory address
00h.
4.14
Acknowledge in Read mode
For all Read commands, the device waits, after each byte read, for an acknowledgment
during the 9
th
bit time. If the bus master does not drive Serial Data (SDA) Low during this
time, the device terminates the data transfer and switches to its Standby mode.
相關PDF資料
PDF描述
M25P16-VMN6TP 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMN3P 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMN3TG 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMN3TP 4 Mbit Uniform Sector, Serial Flash Memory
M25P16-VMN6G 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
M24C32-BN6 功能描述:電可擦除可編程只讀存儲器 5.5V 32K (4Kx8) RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M24C32-DFDW6TP 功能描述:電可擦除可編程只讀存儲器 32 Kbit I2C EEProm 4kB 2.5V to 5.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M24C32-DFMC6TG 功能描述:電可擦除可編程只讀存儲器 32 Kbit I2C EEProm 4kB 2.5V to 5.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M24C32-DFMN6TP 功能描述:電可擦除可編程只讀存儲器 32 Kbit I2C EEProm 4kB 2.5V to 5.5V RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8
M24C32-DRDW3TP/K 功能描述:EEPROM I2C 512KB 8TSSOP 制造商:stmicroelectronics 系列:- 包裝:剪切帶（CT） 零件狀態:有效 格式 - 存儲器:EEPROMs - 串行 存儲器類型:EEPROM 存儲容量:32K（4K x 8） 速度:1MHz 接口:I2C，2 線串口 電壓 - 電源:1.8 V ~ 5.5 V 工作溫度:-40°C ~ 125°C（TA） 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 供應商器件封裝:8-TSSOP 標準包裝:1
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*