參數資料
型號： LXT9860AHC
英文描述： Controller Miscellaneous - Datasheet Reference
中文描述： 控制器雜項-數據表參考
文件頁數： 18/96頁
文件大?。?/td> 1309K
代理商： LXT9860AHC
LXT980/980A Dual-Speed, 5-Port Fast Ethernet Repeater
18
Datasheet
131
RBIAS
Analog
RBIAS.
Used to provide bias current for internal circuitry. The 100
μ
A bias
current is provided through an external 22.1 k
,
1%
resistor to GNDA.
27, 130
GNDA
Analog
Analog Ground.
78
RPS_PRES
TTL Input
PD
Redundant Power Supply Present.
Active High input indicates presence of
redundant power supply. Tie Low if not used.
77
RPS_FAULT
TTL Input
PU
Redundant Power Supply Fault.
Active Low input indicates redundant power
supply fault. The state of this input is reflected in the RPS_LED output (refer to
Table 8 on page 16
). Tie High if not used.
Table 10. PROM Interface Signal Descriptions
Pin
Symbol
Type
1
Description
67
PROM_CLK
Tri-State TTL I/O,
PD
PROM Clock.
1 MHz clock for reading PROM data (ChipID=0).
If a PROM is not used, this pin must be tied Low.
68
PROM_CS
Tri-State
TTL Output
PROM Chip Select.
Selects EPROM. Active High signal driven by chip
with ID of 0.
69
PROM_DTOUT
Tri-State
TTL Output
PROM Data Output.
Selects read instruction for EPROM. Active High
signal driven only by chip with ID of 0.
70
PROM_DTIN
TTL Input, PD
PROM Data Input.
If PROM not used, input tied Low or High.
1. PD = Input contains pull-down.
TTL = Transistor-Transistor Logic.
Table 11. Miscellaneous Signal Descriptions
Pin
Symbol
Type
1
Description
53
RESET
Schmitt CMOS
Input
NC
Reset.
This active Low input causes internal circuits, state machines, and
counters to reset (address tracking registers do not reset). On power-up,
devices should not be brought out of reset until the power supply has stabilized
and reached 4.5V. When there are multiple devices, it is recommended that all
be supplied by a common reset that is driven by an
‘
LS14 or similar device.
54
CLK25
Schmitt CMOS
Input
25 MHz system clock.
Drive with MOS levels.
71
72
73
CHIPID0
CHIPID1
CHIPID2
TTL Input, PD
Chip ID.
These pins assign unique ChipIDs to as many as eight devices on a
single board. One device on each board must be assigned ChipID = 0.
1. NC = No Clamp. Pad will not clamp input in the absence of power.
PD = Input contains pull-down.
TTL = Transistor-Transistor Logic.
Table 9. Power Supply and Indication Signal Descriptions (Continued)
Pin
Symbol
Type
1
Description
1. PU = Input contains pull-up.
PD = Input contains pull-down.
TTL = Transistor-Transistor Logic.
相關PDF資料
PDF描述
LXT9860HC Controller Miscellaneous - Datasheet Reference
LXT9863HC LAN HUB CONTROLLER
LXT9880AGE Controller Miscellaneous - Datasheet Reference
LXT9880AHC Controller Miscellaneous - Datasheet Reference
LXT9880HC Controller Miscellaneous - Datasheet Reference
相關代理商/技術參數
參數描述
LXT9860HC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference
LXT9863 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Umnmanaged Repeater
LXT9863HC 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN HUB CONTROLLER
LXT9880 制造商:INTEL 制造商全稱:Intel Corporation 功能描述:Advanced 10/100 Repeater with Intergrated Management
LXT9880AGE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Controller Miscellaneous - Datasheet Reference
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*