參數資料
型號： LXT362PE
英文描述： PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC
中文描述： 的PCM收發器|單|的T 1（DS1的）|的CMOS | LDCC | 28腳|塑料
文件頁數： 24/52頁
文件大?。?/td> 1187K
代理商： LXT362PE
LXT361
—
Integrated T1/E1 LH/SH Transceiver for DS1/DSX-1 or PRI Applications
24
Datasheet
3.5.5
Other Diagnostic Reports
3.5.5.1
Receive Line Attenuation Indication
The Equalizer Status Register (ESR) provides an approximation of the line attenuation encountered
by the device. The four most significant bits of the register (ESR.LATN7:4) indicate line
attenuation in approximately 2.9 dB steps for both T1 and E1 operation of the receive equalizer.
For instance, if ESR.LATN7:4 is 10 (decimal), then the receiver is seeing a signal attenuated by
approximately 29 dB (2.9 dB x 10) of cable loss.
3.5.5.2
Built-In Self Test
LXT361 provides a Built-In Self Test (BIST) capability. The BIST exercises the internal circuits by
providing an internal QRSS pattern, running it through the encoders and the transmit drivers then
looping it back through the receive equalizer, jitter attenuator and decoders to the QRSS pattern
detection circuitry. If all the blocks in this data path function correctly, the receive pattern detector
locks onto the pattern. It then pulls INT Low and sets the following bits:
TSR.TQRSS = 1
PSR.QRSS = 1
PSR.BIST = 1
Note that during BIST, the TPOS/TNEG inputs must remain at logic level = 0
The most reliable test will result when a separate TCLK and MCLK are applied and the Line
Build-Out (LBO) is set to -22.5 dB (CR1.EC4:1 = 011x).
3.6
Parallel Microprocessor Interface
The LXT361 multiplexed address/data bus and timing/control signals are compatible with both the
Intel and Motorola microprocessors. See
Figure 16
and
Figure 17
for the I/O timing diagram for
each bus. The LXT361 detects and distinguishes between Intel and Motorola timing and then
automatically selects the appropriate bus timing. The maximum recommended processor speed for
an Intel device is 20 MHz; for a Motorola device, 16.78 MHz. See
“
Test Specifications
”
on
page 36
for microprocessor interface timing details.
The LXT361 contains five read/write and three read-only registers for control and status purposes.
Table 6 on page 26
is a summary of the registers.
Table 7
through
Table 15
identify and explain the
function of the register bits.
3.6.1
Interrupt Handling
The LXT361 provides a latched interrupt output pin (INT). When enabled, a change in any of the
Performance Status Register bits will generate an interrupt. An interrupt can also be generated
when the elastic store overflows (TSR.ESOVR) or underflows (TSR.ESUNF). When an interrupt
occurs, the INT output pin is pulled Low. Note that the output stage of the INT pin has internal
pull-down only. Therefore, each device that shares the INT line
requires an
external pull-up
resistor
.
相關PDF資料
PDF描述
LXT362QE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT363LE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT363PE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC
LXT363QE PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT360LE PCM TRANSCEIVER|SINGLE|CEPT PCM-30/E-1|CMOS|QFP|44PIN|PLASTIC
相關代理商/技術參數
參數描述
LXT362QE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT363LE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT363PE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|LDCC|28PIN|PLASTIC
LXT363QE 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCM TRANSCEIVER|SINGLE|T-1(DS1)|CMOS|QFP|44PIN|PLASTIC
LXT36X/35X 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LXT36x/35x - LXT36x/35x Master Clock Requirements
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*