- 您現在的位置：買賣IC網 > PDF目錄11595 > LTC4278IDKD#PBF (Linear Technology)IC PD IEEE 802.3AT 25.5W 32-DFN PDF資料下載
參數資料
| 型號： | LTC4278IDKD#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 17/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PD IEEE 802.3AT 25.5W 32-DFN |
| 產品培訓模塊： | Power over Ethernet |
| 標準包裝： | 52 |
| 控制器類型： | 供電設備接口控制器（PD） |
| 接口： | IEEE 802.3af |
| 電源電壓： | 4.5 V ~ 20 V |
| 電流 - 電源： | 6.4mA |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 32-DFN（7x4）裸露焊盤 |
| 包裝： | 管件 |
| 產品目錄頁面： | 1338 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC4278
24
4278fc
to transformer leakage inductance. The latter causes a
voltage spike on the primary side, not directly related to
output voltage. Some time is also required for internal
settling of the feedback amplifier circuitry. In order to
maintain immunity to these phenomena, a fixed delay is
introduced between the switch turn-off command and the
enabling of the feedback amplifier. This is termed “enable
delay.” In certain cases where the leakage spike is not
sufficiently settled by the end of the enable delay period,
regulation error may result. See the subsequent sections
for further details.
Collapse Detect
Once the feedback amplifier is enabled, some mechanism
is then required to disable it. This is accomplished by a
collapse detect comparator, which compares the flyback
voltage (FB) to a fixed reference, nominally 80% of VFB.
When the flyback waveform drops below this level, the
feedback amplifier is disabled.
Minimum Enable Time
The feedback amplifier, once enabled, stays on for a fixed
minimum time period, termed “minimum enable time.”
This prevents lockup, especially when the output voltage
is abnormally low, e.g., during start-up. The minimum
enable time period ensures that the VCMP node is able to
“pump up” and increase the current mode trip point to
the level where the collapse detect system exhibits proper
operation. This time is set internally.
Effects of Variable Enable Period
The feedback amplifier is enabled during only a portion of
thecycletime.Thiscanvaryfromthefixedminimumenable
time described to a maximum of roughly the off switch
time minus the enable delay time. Certain parameters of
feedback amp behavior are directly affected by the variable
enable period. These include effective transconductance
and VCMP node slew rate.
Load Compensation Theory
The LTC4278 uses the flyback pulse to obtain information
about the isolated output voltage. An error source is
caused by transformer secondary current flow through
the synchronous MOSFET RDS(ON) and real life nonzero
impedances of the transformer secondary and output
capacitor. This was represented previously by the
expression, ISEC(ESR+RDS(ON)).However,itisgenerally
more useful to convert this expression to effective output
impedance. Because the secondary current only flows
during the off portion of the duty cycle (DC), the effective
outputimpedanceequalsthelumpedsecondaryimpedance
divided by off time DC.
Since the off-time duty cycle is equal to 1 – DC, then:
RS(OUT) =
ESR
+RDS(ON)
1– DC
where:
RS(OUT) = effective supply output impedance
DC = duty cycle
RDS(ON) and ESR are as defined previously
This impedance error may be judged acceptable in less
critical applications, or if the output load current remains
relativelyconstant.Inthesecases,theexternalFBresistive
divider is adjusted to compensate for nominal expected
error. In more demanding applications, output impedance
error is minimized by the use of the load compensation
function. Figure 11 shows the block diagram of the load
compensation function. Switch current is converted to a
voltagebytheexternalsenseresistor,averagedandlowpass
filtered by the internal 50k resistor RCMPF and the external
capacitor on CCMP. This voltage is impressed across the
external RCMP resistor by op amp A1 and transistor Q3
producingacurrentatthecollectorofQ3thatissubtracted
from the FB node. This effectively increases the voltage
requiredatthetopoftheR1/R2feedbackdividertoachieve
equilibrium.
The average primary-side switch current increases to
maintain output voltage regulation as output loading
increases. The increase in average current increases RCMP
resistor current which affects a corresponding increase
in sensed output voltage, compensating for the IR drops.
APPLICATIONS INFORMATION
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8873MML | IC ETHERNET SWITCH 3PORT 64-LQFP |
| V72A3V3C264BG2 | CONVERTER MOD DC/DC 3.3V 264W |
| V72A3V3C264BG | CONVERTER MOD DC/DC 3.3V 264W |
| V72A3V3C264BF3 | CONVERTER MOD DC/DC 3.3V 264W |
| KSZ8851-16MLLI | IC MAC CTLR 1PORT W/BUS 48-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4278IDKDTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support |
| LTC4280 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280CUFD | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Hot Swap Controller with I2C Compatible Monitoring |
| LTC4280CUFD#PBF | 功能描述:IC CONTROLLER HOT SWAP QFN-24 RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4280CUFD#TRPBF | 功能描述:IC CTLR HOT SWAP I2C MON 24QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。