- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4274CUHF#PBF (Linear Technology)IC CONTROLLER POE 38-QFN Datasheet資料下載
參數資料
| 型號： | LTC4274CUHF#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 15/28頁 |
| 文件大小： | 702K |
| 描述： | IC CONTROLLER POE 38-QFN |
| 標準包裝： | 52 |
| 類型： | 以太網供電 PSE 控制器（PoE） |
| 應用： | 供電設備（PSE） |
| 內部開關： | 無 |
| 電流限制： | 可調 |
| 電源電壓： | 3 V ~ 4.3 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 38-QFN |
| 供應商設備封裝： | 38-QFN（5x7）裸露焊盤 |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁當前第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC4274
15
4274fd
OPERATION
power that the PSE has available. The classification step
is optional; if a PSE chooses not to classify a PD, it must
assume that the PD is a 13W (full 802.3af power) device.
New in 802.3at
The newer 802.3at standard supersedes 802.3af and brings
several new features:
" A PD may draw as much as 25.5W. Such PDs (and the
PSEs that support them) are known as Type 2. Older
13W 802.3af equipment is classified as Type 1. Type 1
PDs will work with all PSEs; Type 2 PDs may require
Type 2 PSEs to work properly. The LTC4274 is designed
to work in both Type 1 and Type 2 PSE designs, and
also supports non-standard configurations at higher
power levels.
" The Classification protocol is expanded to allow Type 2
PSEs to detect Type 2 PDs, and to allow Type 2 PDs to
determine if they are connected to a Type 2 PSE. Two
versions of the new Classification protocol are avail-
able: an expanded version of the 802.3af Class Pulse
protocol, and an alternate method integrated with the
existing LLDP protocol (using the Ethernet data path).
The LTC4274 fully supports the new Class Pulse protocol
and is also compatible with the LLDP protocol (which
is implemented in the data communications layer, not
in the PoE circuitry).
" Fault protection current levels and timing are adjusted
to reduce peak power in the MOSFET during a fault;
this allows the new 25.5W power levels to be reached
using the same MOSFETs as older 13W designs.
BACKWARDS COMPATIBILITY
The LTC4274 is fully software and pin compatible with
the LTC4266 if only port 1 was used.
The LTC4274 is designed to be backward compatible with
earlier PSE chips in both software and pin functions. Exist-
ing systems using either the LTC4258 or LTC4259A (or
compatible) devices can be substituted with the LTC4274
without software or PCB layout changes if only port 1 was
used; only minor BOM changes are required to implement
a fully compliant 802.3at design.
Because of the backwards compatibility features, some of
the internal registers are redundant or unused when the
LTC4274 is operated as recommended. For more details
on usage in compatibility mode, refer to the LTC4258/
LTC4259A device data sheets.
Special Compatibility Mode Notes
" The LTC4274 can use either 0.5? or 0.25? sense
resistors, while the LTC425x chips always used 0.5?
To maintain compatibility, if the AUTO pin is low when
the LTC4274 powers up it assumes the sense resistor
is 0.5? if it is high at power up, the LTC4274 assumes
0.25? The resistor value setting can be reconfigured
at any time after power up. In particular, systems that
use 0.25?sense resistors and have AUTO tied low
must reconfigure the resistor settings after power up.
" The LTC4259A included both AC and DC disconnect
sensing circuitry, but the LTC4274 has only DC discon-
nect sensing. For the sake of compatibility, register
bits used to enable AC disconnect in the LTC4259A are
implemented in the LTC4274, but they simply mirror
the bits used for DC disconnect.
" The LTC4258 and LTC4259A required 10k resistors
between the OUTn pins and the drains of the external
MOSFETs. These resistors must be shorted or replaced
with zero ohm jumpers when using the LTC4274.
" The LTC4258 and LTC4259A included a BYP pin,
decoupled to AGND with 0.1糉. This pin changes to
the MID pin on the LTC4274. The capacitor should be
removed for Endspan applications, or replaced with a
zero ohm jumper for Midspan applications.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4280CUFD#PBF | IC CONTROLLER HOT SWAP QFN-24 |
| LTC4300-1IMS8#TRPBF | IC HOTSWAP 2WIRE BUS BUFFR 8MSOP |
| LTC4300A-2IMS8#TRPBF | IC BUFFER BUS 2WR HOTSWAP 8-MSOP |
| LTC4301IDD | IC BUFFER BUS HOTSWAP 2WR 8DFN |
| LTC4301LIDD#TRPBF | IC BUFFER BUS HOTSWAP 2WR 8DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4274IUHF#PBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 38-Pin QFN EP 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:IC POE IEEE 802.3AT 38-QFN 制造商:Linear Technology 功能描述:IC POE CNTRL 38QFN 制造商:Linear Technology 功能描述:IC, POE, CNTRL, 38QFN 制造商:Linear Technology 功能描述:IC, POE CONTROLLER, 3.6V, QFN-38; Input Voltage:3.6V; Supply Current:1.1mA; Digital IC Case Style:QFN; No. of Pins:38; Frequency:1MHz; Operating Temperature Min:-40C; Operating Temperature Max:85C; MSL:MSL 1 - Unlimited ;RoHS Compliant: Yes |
| LTC4274IUHF#PBF | 制造商:Linear Technology 功能描述:IC POE CONTROLLER 3.6V QFN-38 |
| LTC4274IUHF#TRPBF | 制造商:Linear Technology 功能描述:POE Controller 25.5W 38-Pin QFN EP |
| LTC42766C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Quad PoE/PoE/LTPoE PSE Controller |
| LTC4278 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:IEEE 802.3at PD with Synchronous No-Opto Flyback Controller and 12V Aux Support |
發布緊急采購，3分鐘左右您將得到回復。