參數資料
型號： LTC4245CG#TRPBF
廠商： Linear Technology
文件頁數： 20/36頁
文件大小： 431K
描述： IC CNTRLR HOT SWAP 36-SSOP
標準包裝： 1,000
類型： 熱交換控制器
應用： CompactPCI?
內部開關： 無
電源電壓： 3.3V，5V，12V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 36-SSOP（0.209"，5.30mm 寬）
供應商設備封裝： 36-SSOP
包裝： 帶卷 (TR)
LTC4245
20
4245fa
Power Bad Fault
A power bad condition exists when any supply output
drops below its power bad threshold for more than
15約 (17約 for V
EEOUT
). This sets bit A2 in the STATUS
register. The HEALTHY# output goes high impedance,
and LOCAL_PCI_RST# pin is pulled low. If the gate of
the supplys MOSFET is enhanced, a power bad fault is
logged in bits F0 to F3 of the FAULT2 register. A circuit
will prevent power bad fault bits being set if the external
MOSFET gate-to-source voltage is low, eliminating false
power bad faults during power-up or power-down. If the
supply output subsequently rises back above the thresh-
old, bit A2 will be cleared, HEALTHY# will pull low and
LOCAL_PCI_RST# will follow PCI_RST#.
BD_SEL# Change of State
Whenever the BD_SEL# pin toggles, bit F6 is set to indi-
cate a change of state. When the BD_SEL# pin goes high,
indicating board removal, all switches turn off immediately.
Bit A6 reports the current state of this pin. If the BD_SEL#
pin is pulled low, indicating a board insertion, all fault bits
except F6 will be cleared. If the sequence bit C6 is set, then
On control bits D1 to D3 are also cleared. If the BD_SEL#
pin remains low for 100ms the state of the ON pin will
be captured in either D0 to D3 or only D0, depending on
sequence bit C6. This turns on the switches if ON pin is
tied high. There is an internal 10糀 pull-up current source
on the BD_SEL# pin from INTV
CC
.
If the system shuts down due to a fault, it may be desirable
to restart the system simply by removing and reinserting
a load card. In cases where the LTC4245 and the switches
reside on a backplane or midplane (as in a PCI Express
application) and the load resides on a plug-in card, the
BD_SEL# pin can be used to detect when the plug-in card
is removed (see Figure 9). Once the plug-in card is rein-
serted the two fault registers are cleared (except for F6).
After 100ms the state of ON pin is latched into bits D0 to
D3. At this point the system will start up again.
If a connection sense on the plug-in card is driving the
BD_SEL# pin, the insertion or removal of the card may
cause the pin voltage to bounce. This will result in clear-
ing the fault register when the card is removed. The pin
can be debounced using a  lter capacitor, C
BD_SEL#
 , on
the BD_SEL# pin as shown in Figure 9. The  lter time is
given by:
 
t
C
ms  礔
FILTER    BD  SEL
=
_    #
"
[    /   ]
123
 
(5)
FET Short Fault
A FET short fault will be reported if the data converter
measures a supplys current sense voltage greater than 7
LSB while the supplys pass transistor is turned off. This
condition sets the FET short present bit, A5, and the FET
short fault bit F5. Reading the On status bits (D4 to D7) and
the ADC current sense voltage data registers (J, M, P, S)
can help debug which supplys MOSFET might be poten-
tially shorted. A false FET short fault might be reported if
an input supply power-up is delayed by more than 500ms
after INTV
CC
 is up.
Fault Alerts
When any of the bits in fault registers E and F are set, an
optional bus alert can be generated by setting the appropri-
ate bit in the ALERT register B. This allows only selected
faults to generate alerts. At power-up the default state is not
to alert on faults. If an alert is enabled, the corresponding
fault will cause the ALERT# pin to pull low. See the Alert
Response Protocol section for more information.
APPLICATIO  S I FOR  ATIO
U
U
U
Figure 9. Plug-In Card Insertion/Removal

+
1.235V
GND
MOTHERBOARD
CONNECTOR   PLUG-IN
CARD
LTC4245G*
*ADDITIONAL DETAILS OMITTED FOR CLARITY
10礎
9
BD_SEL#   10
C
BD_SEL#
4245 F09
相關PDF資料
PDF描述
LTC4251-2CS6#TRPBF IC CTRLR HOTSWAP NEGVOLT SOT23-6
LTC4252A-1IMS#TRPBF IC CNTRLR HOTSWAP NEGVOLT 10MSOP
LTC4253ACGN#TRPBF IC HOT SWAP CONTRLR -48V 16-SSOP
LTC4257CS8 IC CTRLR INTFACE PWR/ETHER 8SOIC
LTC4260IUH#PBF IC HOT SWAP CNTRL I2C 32-QFN
相關代理商/技術參數
參數描述
LTC4245CUHF 制造商:LINER 制造商全稱:Linear Technology 功能描述:Multiple Supply Hot Swap Controller with I2C Compatible Monitoring
LTC4245CUHF#PBF 功能描述:IC CNTRLR HOT SWAP 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4245CUHF#TRPBF 功能描述:IC CNTRLR HOT SWAP 38-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
LTC4245IG 制造商:LINER 制造商全稱:Linear Technology 功能描述:Multiple Supply Hot Swap Controller with I2C Compatible Monitoring
LTC4245IG#PBF 功能描述:IC CNTRLR HOT SWAP 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*