- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4222CG#PBF (Linear Technology)IC CTRLR DUAL HOT SWAP 36-SSOP Datasheet資料下載
參數資料
| 型號： | LTC4222CG#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 20/32頁 |
| 文件大?。?/td> | 339K |
| 描述： | IC CTRLR DUAL HOT SWAP 36-SSOP |
| 標準包裝： | 37 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.9 V ~ 29 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC4222
20
4222fb
APPLICATIONS INFORMATION
The address is set with the help of Table 1, which indi-
cates binary address 1000111 corresponds to address
4. Address 4 is set by setting ADR2 low, ADR1 open and
ADR0 high.
Next the value of R5 and R6 are chosen to be the default
values 10?and 15k?as discussed previously.
In addition a 0.1礔 ceramic bypass capacitor is placed on
the INTV
CC
pin.
Layout Considerations
To achieve accurate current sensing, a Kelvin connection
is required. The minimum trace width for 1oz copper
foil is 0.02" per amp to make sure the trace stays at a
reasonable temperature. Using 0.03" per amp or wider
is recommended. Note that 1oz copper exhibits a sheet
resistance of about 530旦. Small resistances add up
quickly in high current applications. To improve noise
immunity, put the resistive dividers to the UV , OV and FB
pins close to the device and keep traces to V
DD
and GND
short. It is also important to put the bypass capacitor for
the INTV
CC
pin, C3, as close as possible between INTV
CC
and GND. 0.1礔 capacitors from the UV pins (and OV pins
through resistor R2) to GND also helps reject supply noise.
Figure 5 shows a layout that addresses these issues. Note
that surge suppressor, Z1 is placed between supply and
ground using wide traces.
Digital Interface
The LTC4222 communicates with a bus master using a
2-wire interface compatible with I
2
C Bus and SMBus, an
I
2
C extension for low power devices. The LTC4222 is a
read-write slave device and supports SMBus bus Read
Byte, Write Byte, Read Word and Write Word commands.
A complete list of the resistors of the LTC4222 is shown
in Table 2. The second word in a Read Word command is
the contents of the subsequent 8-bit register. The second
word in a Write Word command is ignored. Data formats
for these commands are shown in Figures 6 to 11.
The LTC4222 interface also features a 25ms timeout feature
to prevent the bus being stuck low if a communication
error occurs. If either the SCL or SDA lines remain low
for more than 25ms the LTC4222 will reset its interface
and release the SDAO pin, freeing the bus to resume
communication.
The LTC4222 also features PMBus compatibility, the in-
terface will not acknowledge unsupported commands and
the internal addresses are in the manufacturer specified
address space under the PMBus specification.
START and STOP Conditions
When the bus is idle, both SCL and SDA are high. A bus
master signals the beginning of a transmission with a start
condition by transitioning SDA from high to low while SCL
is high, as shown in Figure 6. When the master has finished
communicating with the slave, it issues a STOP condition
by transitioning SDA from low to high while SCL is high.
The bus is then free for another transmission.
I
2
C Device Addressing
Twenty seven distinct bus addresses are available using
three 3-state address pins, ADR0, ADR1 and ADR2. Table 1
shows the correspondence between pin states and ad-
dresses. In addition, the LTC4222 responds to two special
addresses. Address (1100 0110) is a mass write address
that writes to all LTC4222s, regardless of their individual
address settings. Mass write can be disabled by setting
register bit 4 in the CONTROL register of channel 2 to zero.
Address (0001 100) is the SMBus Alert Response Address.
If the LTC4222 is pulling low on the ALERT pin due to an
Figure 5. Recommended Layout
SS
CONFIG
INTV
CC
GND
LTC4222UHD
4222 F05
VIAS TO
GROUND
PLANE
VIA TO
GROUND
PLANE
SENSE RESISTOR R
S
I
LOAD
C
SS
C3
R2
R3
C
F
Z1
R1
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4223CDHD-2#PBF | IC CNTRLR HOT SWAP DUAL 16-DFN |
| LTC4224IDDB-2#TRPBF | IC CNTRLR HOT SWAP DUAL 10-DFN |
| LTC4225IGN-1#PBF | IC CONTROLLER HOT SWAP 24-SSOP |
| LTC4230CGN#TRPBF | IC CONTRLLR HOT SWAP TRPL 20SSOP |
| LTC4232CDHC#TRPBF | IC CTLR HOT SWAP 5A 16-DFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4222CG-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
| LTC4222CUH#PBF | 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4222CUH#TRPBF | 功能描述:IC CTRLR DUAL HOT SWAP 32-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4222CUH-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
| LTC4222CUH-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
發布緊急采購，3分鐘左右您將得到回復。