- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4221IGN#TRPBF (Linear Technology)IC CTRLR HOTSWAP DUAL 16SSOP Datasheet資料下載
參數資料
| 型號： | LTC4221IGN#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 272K |
| 描述： | IC CTRLR HOTSWAP DUAL 16SSOP |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 1 V ~ 13.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
22
LTC4221
4221fa
supply voltages, the LTC4221 can drive any MOSFET rated
with 4.5V or 2.5V gate drive. For higher supply voltages up
to 13.5V, the LTC4221 can drive any MOSFET rated with
a 10V or 4.5V gate drive. The selected MOSFET should
fulfill two V
GS
criteria:
1. Positive V
GS
absolute maximum rating > LTC4221s
maximum 擵
GATE
.
2. Negative V
GS
absolute maximum rating > supply volt-
age. The gate of the MOSFET can discharge faster than
V
OUT
when shutting down the MOSFET with a large
C
LOAD
.
If one of the conditions cannot be met, an external zener
clamp shown on Figure 15 can be used. The clamp
network is connected from each channels GATE to the
V
OUT
pins. V
GS
is clamped in both directions and R
G
limits
the current flow into the GATEn pins internal zener clamp
during transient events.
A MOSFET with a V
GS
absolute maximum rating of ?0V
meets the two criteria for all the LTC4221 application ranges
from 1V to 13.5V. Typically most 10V gate rated MOSFETs
have V
GS
absolute maximum ratings of ?0V or greater, so
no external V
GS
zener clamp is needed. There are 4.5V gate
rated MOSFETs with V
GS
absolute maximum ratings of
?0V. In addition to the MOSFET gate drive rating and V
GS
absolute maximum rating, other criteria such as V
BDSS
,
I
D(MAX)
, R
DS(ON)
, P
D
, ?/DIV>
JA
, T
J(MAX)
and maximum safe
operating area (SOA) should also be carefully reviewed.
V
BDSS
should exceed the maximum supply voltage inclu-
sive of spikes and ringing. I
D(MAX)
must exceed the maxi-
mum short-circuit current in the channel during a fault
condition. R
DS(ON)
determines the MOSFET V
DS
which to-
gether with V
RSENSE
yields an error in the V
OUT
voltage. For
example, at 1V V
CC2
, V
DS
+ V
RSENSE2
= 50mV gives a 5%
V
OUT2
error. At higher V
CC
voltages the V
DS
requirement can
be relaxed in which case the MOSFETs thermal require-
ments (P
D
, T
J(MAX)
, SOA) may limit the value of R
DS(ON)
.
The power dissipated in the MOSFET is (I
LOAD
)
2
" R
DS(ON)
and this should be less than the maximum power dissipa-
tion, P
D
, allowed in that package. Given power dissipation,
the MOSFET junction temperature, T
J
can be computed
from the operating temperature (T
A
) and the MOSFET
package thermal resistance (?/DIV>
JA
). The operating T
J
should
be less than the T
J(MAX)
specification. The V
DS
" I
LOAD
figure must also be well within the manufacturers recom-
mended safe operating area (SOA) with sufficient margin.
These three thermal parameters must not be exceeded for
all conditions in a channel including normal mode opera-
tion, start-up with or without current limit, fault and
autoretry after a fault. To ensure a reliable design, fault
tests should be evaluated in the laboratory.
V
CC
Transient Protection
Good engineering practice calls for bypassing the supply
rail of any analog circuit. Bypass capacitors are often
placed at the supply connection of every active device, in
addition to one or more large value bulk bypass capacitors
per supply rail. If power is connected abruptly, the large
bypass capacitors slow the rate of rise of the supply
voltage and heavily damp any parasitic resonance of lead
or PC track inductance working against the supply bypass
capacitors.
The opposite is true for LTC4221 Hot Swap circuits
mounted on plug-in cards since controlling the surge
current to bypass capacitors at plug-in is the primary
motivation for the Hot Swap controller. In most cases,
there is no supply bypass capacitor present on the pow-
ered supply voltage side of the MOSFET switch. Although
wire harness, backplane and PCB trace inductances are
usually small, these can create large spikes when large
currents are suddenly drawn, cut off or limited. Abrupt
intervention can prevent subsequent damage caused by a
catastrophic fault but it does cause a large supply tran-
sient. These ringing transients appear as a fast edge on
APPLICATIO S I FOR ATIO
U
U
U
*USER SELECTED VOLTAGE CLAMP
(A LOW BIAS CURRENT ZENER DIODE IS RECOMMENDED)
1N4688 (5V)
1N4692 (7V): LOGIC-LEVEL MOSFET
1N4695 (9V)
1N4702 (15V): STANDARD-LEVEL MOSFET
R
SENSE
GATE
4221 F15
Q1
R
G
200?/DIV>
D1* D2*
V
CC
V
OUT
Figure 15. Gate Protection Zener Clamp
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4222CG#PBF | IC CTRLR DUAL HOT SWAP 36-SSOP |
| LTC4223CDHD-2#PBF | IC CNTRLR HOT SWAP DUAL 16-DFN |
| LTC4224IDDB-2#TRPBF | IC CNTRLR HOT SWAP DUAL 10-DFN |
| LTC4225IGN-1#PBF | IC CONTROLLER HOT SWAP 24-SSOP |
| LTC4230CGN#TRPBF | IC CONTRLLR HOT SWAP TRPL 20SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4222 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller |
| LTC4222_12 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller |
| LTC4222CG#PBF | 功能描述:IC CTRLR DUAL HOT SWAP 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC4222CG#TRPBF | 功能描述:IC CTRLR DUAL HOT SWAP 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4222CG-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Hot Swap Controller with I2C Compatible Monitoring |
發布緊急采購，3分鐘左右您將得到回復。