- 您現在的位置：買賣IC網 > PDF目錄358876 > LM80CIMT-31 (National Semiconductor Corporation) Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor PDF資料下載
參數資料
| 型號： | LM80CIMT-31 |
| 廠商： | National Semiconductor Corporation |
| 英文描述： | Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor |
| 中文描述： | 串行接口ACPI的兼容微處理器系統硬件監視器 |
| 文件頁數： | 14/29頁 |
| 文件大小： | 435K |
| 代理商： | LM80CIMT-31 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Functional Description
(Continued)
6.0 FAN INPUTS
Inputs are provided for signals from fans equipped with ta-
chometer outputs. These are logic-level inputs with an ap-
proximate threshold of V
+
/2. Signal conditioning in the LM80
accommodates the slow rise and fall times typical of fan ta-
chometer outputs. The maximum input signal range is 0 to
V
+
. In the event these inputs are supplied from fan outputs
which exceed 0 to V+, either resistive division or diode
clamping must be included to keep inputs within an accept-
able range, as shown in Figure 7 R2 is selected so that it
does not develop excessive error voltage due to input leak-
age. R1 is selected based on R2 to provide a minimum input
of 2V and a maximum of V
+
. R1 should be as low as possible
to provide the maximum possible input up to V
+
for best
noise immunity. Alternatively, use a shunt reference or zener
diode to clamp the input level.
If fans can be powered while the power to the LM80 is off,
the LM80 inputs will provide diode clamping. Limit input cur-
rent to the Input Current atAny Pin specification shown in the
ABSOLUTE MAXIMUM RATINGS section. In most cases,
open collector outputs with pull-up resistors inherently limit
this current. If this maximum current could be exceeded, ei-
ther a larger pull up resistor should be used or resistors con-
nected in series with the fan inputs.
The Fan Inputs gate an internal 22.5 kHz oscillator for one
period of the Fan signal into an 8-bit counter (maximum
count = 255). The default divisor, located in the VID/Fan Di-
visor Register, is set to 2 (choices are 1, 2, 4, and 8) provid-
ing a nominal count of 153 for a 4400 rpm fan with two
pulses per revolution. Typical practice is to consider 70% of
normal RPM a fan failure, at which point the count will be
219.
Determine the fan count according to:
Note that Fan 1 and Fan 2 Divisors are programmable via
the Fan Divisor/RST_OUT/OS Register.
FAN1 and FAN2 inputs can also be programmed to be level
sensitive digital inputs.
Fans that provide only one pulse per revolution would re-
quire a divisor set twice as high as fans that provide two
pulses, thus maintaining a nominal fan count of 153. There-
fore the divisor should be set to 4 for a fan that provides 1
pulse per revolution with a nominal RPM of 4400.
www.national.com
14
相關PDF資料 |
PDF描述 |
|---|---|
| LM832 | LM832 Dynamic Noise Reduction System DNR |
| LM832M | LM832 Dynamic Noise Reduction System DNR |
| LM832N | LM832 Dynamic Noise Reduction System DNR |
| LM833D | DUAL OPERATIONAL AMPLIFIER |
| LM833P | Voltage-Feedback Operational Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LM80CIMT3NOPB | 制造商:Texas Instruments 功能描述:Processor Supervisor 24-Pin TSSOP Rail |
| LM80CIMT5 | 制造商:Texas Instruments 功能描述: |
| LM80CIMT-5 | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM80CIMT-5/NOPB | 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel |
| LM80CIMT-5/NOPB | 制造商:Texas Instruments 功能描述:Temperature Sensor IC |
發布緊急采購，3分鐘左右您將得到回復。