參數資料
型號： LM80CIMT-31
廠商： National Semiconductor Corporation
英文描述： Serial Interface ACPI-Compatible Microprocessor System Hardware Monitor
中文描述： 串行接口ACPI的兼容微處理器系統硬件監視器
文件頁數： 13/29頁
文件大?。?/td> 435K
代理商： LM80CIMT-31
Functional Description
(Continued)
A typical application, such as is shown in Figure 6 might se-
lect the input voltage divider to provide 1.9V at the analog in-
puts of the LM80. This is sufficiently high for good resolution
of the voltage, yet leaves headroom for upward excursions
from the supply of about 25%. To simplify the process of re-
sistor selection, set the value of R2 first. Select a value for
R2 or R4 between 10 k
and 100 k
This is low enough to
avoid errors due to input leakage currents yet high enough to
both protect the inputs under overdrive conditions as well as
minimize loading of the source. Then select R1 or R3 to pro-
vide a 1.9V input as show in Figure 6
For positive input voltages the equation for calculating R1 is
as follows:
R1 = [ (V
S
V
IN
) / V
IN
] R2
For negative input voltages the equation for Calculating R3
is as follows:
R3 = [ (V
S
V
IN
) / (V
IN
5V)] R4
The analog inputs have internal diodes that clamp inputs ex-
ceeding the power supply and ground. Exceeding any ana-
log input has no detrimental effect on other channels. The in-
put diodes will also clamp voltages appearing at the inputs of
an un-powered LM80. External resistors should be included
to limit input currents to the values given in the ABSOLUTE
MAXIMUM RATINGS for Input Current At Any Pin. Inputs
with the attenuator networks will usually meet these require-
ments. If it is possible for inputs without attenuators to be
turned on while LM80 is powered off, additional resistors of
about 10 k
should be added in series with the inputs to limit
the input current.
Voltage
Measure-
ments
(V
S
)
+2.5V
+3.3V
+5.0V
+12V
12V
5V
R1 or
R3
R2 or
R4
Voltage
at
Analog Inputs
( ADC code 190)
+1.9V
+1.9V
+1.9V
+1.9V
+1.9V
+1.9V
23.7 k
22.1 k
24 k
160 k
160 k
36 k
75 k
30 k
14.7 k
30.1 k
35.7 k
16.2 k
5.0 LAYOUT AND GROUNDING
Analog inputs will provide best accuracy when referred to the
AGND pin or a supply with low noise. A separate,
low-impedance ground plane for analog ground, which pro-
vides a ground point for the voltage dividers and analog
components, will provide best performance but is not man-
datory. Analog components such as voltage dividers should
be located physically as close as possible to the LM80.
The power supply bypass, the parallel combination of 10 μF
(electrolytic or tantalum) and 0.1 μF (ceramic) bypass ca-
pacitors connected between pin 9 and ground, should also
be located as close as possible to the LM80.
DS100040-11
FIGURE 6. Input Examples. Resistor values shown in
table provide approximately 1.9V at the analog inputs.
www.national.com
13
相關PDF資料
PDF描述
LM832 LM832 Dynamic Noise Reduction System DNR
LM832M LM832 Dynamic Noise Reduction System DNR
LM832N LM832 Dynamic Noise Reduction System DNR
LM833D DUAL OPERATIONAL AMPLIFIER
LM833P Voltage-Feedback Operational Amplifier
相關代理商/技術參數
參數描述
LM80CIMT3NOPB 制造商:Texas Instruments 功能描述:Processor Supervisor 24-Pin TSSOP Rail
LM80CIMT5 制造商:Texas Instruments 功能描述:
LM80CIMT-5 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
LM80CIMT-5/NOPB 功能描述:監控電路 RoHS:否 制造商:STMicroelectronics 監測電壓數: 監測電壓: 欠電壓閾值: 過電壓閾值: 輸出類型:Active Low, Open Drain 人工復位:Resettable 監視器:No Watchdog 電池備用開關:No Backup 上電復位延遲（典型值）:10 s 電源電壓-最大:5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:UDFN-6 封裝:Reel
LM80CIMT-5/NOPB 制造商:Texas Instruments 功能描述:Temperature Sensor IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*