- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN91C100 (SMSC Corporation) FEAST⑩ Fast Ethernet Controller PDF資料下載
參數資料
| 型號： | LAN91C100 |
| 廠商： | SMSC Corporation |
| 英文描述： | FEAST⑩ Fast Ethernet Controller |
| 中文描述： | 宴⑩快速以太網控制器 |
| 文件頁數： | 30/101頁 |
| 文件大?。?/td> | 312K |
| 代理商： | LAN91C100 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁
30
I/O SPACE - BANK1
OFFSET
0
NAME
CONFIGURATION REGISTER
TYPE
READ/WRITE
SYMBOL
CR
The Configuration Register holds bits that define the adapter configuration and are not expected to
change during run-time. This register is part of the EEPROM-saved setup.
HIGH
BYTE
MII
SELECT
NO WAIT
FULL
STEP
AUI
SELECT
1
X
X
0
X
0
0
0
LOW
BYTE
1
0
RESERVED
INT SEL1
INT SEL0
1
0
1
1
0
0
0
X
MII SELECT Used to select the network
interface port. When set, the LAN91C100 will
use its MII port and interface a PHY device at
the nibble rate. When clear, the LAN91C100
will use its 10 Mbps ENDEC interface. This bit
drives the MII SEL pin. Switching between ports
should be done with transmitter and receiver
disabled and no transmit/receive packets in
progress.
NO WAIT When set, does not request
additional wait states. An exception to this are
accesses to the Data Register if not ready for a
transfer. When clear, negates IOCHRDY for
two to three clocks on any cycle to the
LAN91C100.
FULL STEP This bit is a general purpose output
port. Its inverse value drives pin nFSTEP and it
is typically connected to SEL pin of the
LAN83C694C. It can be used to select the
signaling mode for the AUI, or as a general
purpose non-volatile configuration pin. Defaults
low.
AUI SELECT This bit is a general purpose
output port. Its value drives pin AUISEL and it
is typically connected to MODE1 pin of the
LAN83C694C. It can be used to select AUI vs.
10BASE-T, or as a general purpose non-volatile
configuration pin. Defaults low.
INT SEL1-0 Used to select one out of four
interrupt pins. The three unused interrupts are
tristated.
INT SEL1
0
0
1
1
INT SEL0
0
1
0
1
PIN USED
INTR0
INTR1
INTR2
INTR3
相關PDF資料 |
PDF描述 |
|---|---|
| LAN91C110 | FEAST FAST ETHERNET CONTROLLER FOR PCMCIA AND GENERIC 16-BIT APPLICATIONS |
| LAN91C96(100TQFP) | LAN Node Controller |
| LAN91C96(100QFP) | LAN Node Controller |
| LAN91C95 | LAN Node Controller |
| LAN91C100FD(208TQFP) | LAN Node Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN91C100FD | 制造商:- 功能描述: 制造商:SMSC 功能描述: |
| LAN91C100-FD | 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST Fast Ethernet Controller with Full Duplex Capability |
| LAN91C100FD(208PQFP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| LAN91C100FD(208TQFP) | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:LAN Node Controller |
| LAN91C100FD_06 | 制造商:SMSC 制造商全稱:SMSC 功能描述:FEAST Fast Ethernet Controller with Full Duplex Capability |
發布緊急采購，3分鐘左右您將得到回復。