- 您現在的位置：買賣IC網 > PDF目錄358741 > LAN8187_06 (SMSC Corporation) 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM PDF資料下載
參數資料
| 型號： | LAN8187_06 |
| 廠商： | SMSC Corporation |
| 英文描述： | 【15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWRTM |
| 中文描述： | 【15kV的ESD保護信息產業部/ RMII快速以太網PHY與HP Auto - MDIX功能和SMSC flexPWRTM |
| 文件頁數： | 12/72頁 |
| 文件大小： | 433K |
| 代理商： | LAN8187_06 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁
±15kV ESD Protected MII/RMII Fast-Ethernet PHY with HP Auto-MDIX and SMSC flexPWR
TM
Datasheet
Chapter 3 Pin Description
SMSC LAN8187/LAN8187I
12
Revision 1.0 (12-14-06)
DATASHEET
This chapter describes the signals on each pin. When a lower case “n” is used at the beginning of the
signal name, it indicates that the signal is active low. For example, nRST indicates that the reset signal
is active low.
3.1
I/O Signals
I
Input. Digital LVCMOS levels.
O
Output. Digital LVCMOS levels.
I/O
Input or Output. Digital LVCMOS levels.
Note:
The digital signals are not 5V tolerant. They are variable voltage from +1.6V to +3.6V.
AI
Input. Analog levels.
AO
Output. Analog levels.
Table 3.1 MII Signals
SIGNAL NAME
TYPE
DESCRIPTION
TXD0
I
Transmit Data 0
: Bit 0 of the 4 data bits that are accepted by
the PHY for transmission.
TXD1
I
Transmit Data 1
: Bit 1 of the 4 data bits that are accepted by
the PHY for transmission.
TXD2
I
Transmit Data 2
: Bit 2 of the 4 data bits that are accepted by
the PHY for transmission
Note:
This signal should be grounded in RMII Mode.
TXD3
I
Transmit Data 3
:
Bit 3 of the 4 data bits that are accepted by
the PHY for transmission.
Note:
This signal should be grounded in RMII Mode
nINT/
TX_ER/
TXD4
I/O
MII Transmit Error
: When driven high, the 4B/5B encode
process substitutes the Transmit Error code-group (/H/) for the
encoded data word. This input is ignored in 10Base-T operation.
MII Transmit Data 4:
In Symbol Interface (5B Decoding) mode,
this signal becomes the MII Transmit Data 4 line, the MSB of the
5-bit symbol code-group.
Notes:
This signal is not used in RMII Mode.
This signal is mux’d with nINT
See
Section 4.10, "(TX_ER/TXD4)/nINT Strapping," on
page 31
for additional information on configuration/strapping
options.
TX_EN
I
Transmit Enable
: Indicates that valid data is presented on the
TXD[3:0] signals, for transmission. In RMII Mode, only TXD[1:0]
have valid data.
TX_CLK
O
Transmit Clock
: 25MHz in 100Base-TX mode. 2.5MHz in
10Base-T mode.
Note:
This signal is not used in RMII Mode
相關PDF資料 |
PDF描述 |
|---|---|
| LAN8187 | High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN83C175 | Ethernet CARDBUS Integrated Controller With Modem Support |
| LAN83C180 | 10/100 FAST ETHERNET PHY TRANSCEIVER |
| LAN83C185 | HIGH PERFORMANCE SINGLE CHIP LOW POWER 10/100 ETHERNET PHYSICAL LAYER TRANSCEIVER |
| LAN83C183-JD | FAST ETHERNET PHYSICAL LAYER DEVICE |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LAN8187I | 制造商:SMSC 制造商全稱:SMSC 功能描述:High-Performance MII and RMII 10/100 Ethernet PHY with HP Auto-MDIX |
| LAN8187I-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN8187-JT | 功能描述:以太網 IC HiPerfrm Ethrnt PHY RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| LAN83C171 | 制造商:SMSC 制造商全稱:SMSC 功能描述:EPIC/XF ACPI/PC 97 Compliant Integrated PCI 10/100 Mbps Fast Ethernet Controller |
| LAN83C171 WAF | 制造商:SMSC 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。