- 您現在的位置：買賣IC網 > PDF目錄67754 > L6566BTR (STMICROELECTRONICS) 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | L6566BTR |
| 廠商： | STMICROELECTRONICS |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.8 A POWER FACTOR CONTROLLER, 900 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | LEAD FREE, SOP-16 |
| 文件頁數： | 51/51頁 |
| 文件大小： | 624K |
| 代理商： | L6566BTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁當前第51頁
L6566B
Pin settings
9/51
5Vcc
Supply voltage of both the signal part of the IC and the gate driver. The internal
high voltage generator charges an electrolytic capacitor connected between this
pin and GND (pin 3) as long as the voltage on the pin is below the turn-on threshold
of the IC, after that it is disabled and the chip is turned on. The IC is disabled as the
voltage on the pin falls below the UVLO threshold. This threshold is reduced at light
load to counteract the natural reduction of the self-supply voltage. Sometimes a
small bypass capacitor (0.1 F typ.) to GND might be useful to get a clean bias
voltage for the signal part of the IC.
6FMOD
Frequency modulation input. When FF mode operation is selected, a capacitor
connected from this pin to GND (pin 3) is alternately charged and discharged by
internal current sources. As a result, the voltage on the pin is a symmetrical
triangular waveform with the frequency related to the capacitance value. By
connecting a resistor from this pin to pin 13 (OSC) it is possible to modulate the
current sourced by the OSC pin and then the oscillator frequency. This modulation
is to reduce the peak value of EMI emissions by means of a spread-spectrum
action. If the function is not used, the pin will be left open.
7CS
Input to the PWM comparator. The current flowing in the MOSFET is sensed
through a resistor, the resulting voltage is applied to this pin and compared with an
internal reference to determine MOSFET’s turn-off. The pin is equipped with 150 ns
min. blanking time after the gate-drive output goes high for improved noise
immunity. A second comparison level located at 1.5 V latches the device off and
reduces its consumption in case of transformer saturation or secondary diode short
circuit. The information is latched until the voltage on the Vcc pin (5) goes below
the UVLO threshold, hence resulting in intermittent operation. A logic circuit
improves sensitivity to temporary disturbances.
8DIS
IC’s latched disable input. Internally the pin connects a comparator that, when the
voltage on the pin exceeds 4.5 V, latches off the IC and brings its consumption to a
lower value. The latch is cleared as the voltage on the Vcc pin (5) goes below the
UVLO threshold, but the HV generator keeps the Vcc voltage high (see pin 1
description). It is then necessary to recycle the input power to restart the IC. For a
quick restart pull pin 16 (AC_OK) below the disable threshold (see pin 16
description). Bypass the pin with a capacitor to GND (pin 3) to reduce noise pick-
up. Ground the pin if the function is not used.
9COMP
Control input for loop regulation. The pin will be driven by the phototransistor
(emitter-grounded) of an optocoupler to modulate its voltage by modulating the
current sunk. A capacitor placed between the pin and GND (3), as close to the IC
as possible to reduce noise pick-up, sets a pole in the output-to-control transfer
function. The dynamics of the pin is in the 2.5 to 5 V range. A voltage below an
internally defined threshold activates burst-mode operation. The voltage at the pin
is bottom-clamped at about 2 V. If the clamp is externally overridden and the
voltage is pulled below 1.4 V the IC will shut down.
10
VREF
An internal generator furnishes an accurate voltage reference (5 V ± 2 %) that can
be used to supply few mA to an external circuit. A small film capacitor (0.1 F typ.),
connected between this pin and GND (3), is recommended to ensure the stability of
the generator and to prevent noise from affecting the reference. This reference is
internally monitored by a separate auxiliary reference and any failure or drift will
cause the IC to latch off.
Table 1.
Pin functions (continued)
N°
Pin
Function
相關PDF資料 |
PDF描述 |
|---|---|
| L6706 | SWITCHING REGULATOR, QCC40 |
| L6717 | DUAL SWITCHING CONTROLLER, 575 kHz SWITCHING FREQ-MAX, QCC48 |
| L6728HTR | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
| L6728H | SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, PDSO10 |
| L6728 | 1.5 A SWITCHING CONTROLLER, 330 kHz SWITCHING FREQ-MAX, DSO10 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| L6566BTR-CUT TAPE | 制造商:ST 功能描述:L6566B Series 23 V 4.6 mA SMPS Multi-Mode Controller Surface Mount - SOIC-16N |
| L6567 | 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:HIGH VOLTAGE DRIVER FOR CFL |
| L6567D | 制造商:STMicroelectronics 功能描述:CFL DRVR 18V 14SOP - Rail/Tube |
| L6569 | 功能描述:功率驅動器IC Hi-Volt Half Bridge RoHS:否 制造商:Micrel 產品:MOSFET Gate Drivers 類型:Low Cost High or Low Side MOSFET Driver 上升時間: 下降時間: 電源電壓-最大:30 V 電源電壓-最小:2.75 V 電源電流: 最大功率耗散: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| L6569 | 制造商:STMicroelectronics 功能描述:IC HALF BRIDGE+OSC 6569 DIP8 |
發布緊急采購，3分鐘左右您將得到回復。