參數資料
型號： L6280
廠商： 意法半導體
英文描述： THREE CHANNELS MULTIPOWER DRIVER SYSTEM
中文描述： 三通道移動電站驅動系統
文件頁數： 11/26頁
文件大?。?/td> 388K
代理商： L6280
Digital/Analog Converters(DACs)
The output current levels are programmed by
5DACs each with 3 bit resolution. Channels1 and
2 each have 2 DACs, one for the left part of the
output stage and the other for the right part.
When the output stage is used to drive only one
load (as with DC motors), the L6280 uses only
the right register. Channel 3 has only 1 DAC.
Microstepping operation is easily performed with
channels1 and 2. The value of each DAC can be
changedin two ways:
a) the new value can be directly generated by
the microprocessor and then loaded into the
specifiedDAC;
b) the value of a DAC can be incremented or
decremented by 1; in this case the microproc-
essor during acceleration or decelerationhas
only to indicate the DAC on which operate
and the type of the operation, reducing the
CPU’s burden.
The correspondencebetween the DAC value and
the Vreflevel is shownin table1.
Table 1
D2
1
1
1
1
0
0
0
0
D1
1
1
0
0
1
1
0
0
D0
1
0
1
0
1
0
1
0
V
ref
UNIT
V
V
V
V
V
V
V
V
1
0.875
0.75
0.625
0.5
0.375
0.25
0.125
Iload = 0 is obtained by disabling all low-side driv-
ers.
Turn ON/OFF Characteristicsand Program Se-
quence
During power-on the Switchmode Power Supply
output stage is turned OFF till V
S
reaches V
PFth
.
The pin Reset Out is held low and remains low till
V
SS
is < V
SSFth
(the power stages and the logic of
the L6280 aredisabled.
Not correct signals coming from the microproces-
sor are then ignored; the microprocessor on the
other hand, receives a low state signal from the
Reset Out pin. When the V
SS
output is stabilized
during a delay t
D
set by the C
D
capacitor, the pin
Reset Out goes to the high level; the microproc-
essor is enabled to work while the L6280 is in
stand-by waiting for a keyword and initialization
sequence.Every command that arrives beforethe
keyword is ignored. At this time the programming
sequencecan start according to the flow diagram
(Fig.12).
At first the Keyword (00111010) has to be sent to
the L6280 to activate the watch - dog function
that begins to control the microprocessor func-
tionality. From this moment the microprocessor
must send periodically the Watch-dog word
(00110101) otherwise its absence is interpreted
as a microprocessor failure: to prevent any dam-
age both in the load and in the IC, the L6280itself
disablesthe power stages.No reset signal is gen-
erated towards the CPU; the system must restart
the sequencefrom Power-ON.
The next step is to set the configuration of chan-
nel 1 and channel 2 output stages by the initiali-
zation word. The configuration can be chosen to
fit in theload characteristics.To do thisthe micro-
processor generates a word with A0, A1 = 0 and
where A2, A3 choose the channel to be config-
ured, D0 to D3 choose the type of configuration
(unipolar, dual half bridge or full bridge; see Data
and Address decoding).Every input configuration
different from the allowed initialization word is ig-
nored.
When the initializationarrives, the L6280 sets the
configuration of the output stage of the chosen
channel. The initialization word has to be re-
peated for the other channel(CH1 or CH2 only).If
two initializations arrive for the same channel, the
L6280 disables the output stages while pin Reset
Out goes low for a time Td to advise the mocro-
processor about the uncorrect condition. The pro-
gram sequence must restart from the Keyword
step. After the initialization step is succesfully
completed the L6280 begins to accept com-
mands. If a command is sent before the relative
channel has been configured, the command is
neglected.
Command can be of three type:
a - selectionof current level loading a DAC;
b - increment or decrement of aDAC;
c - selection of the driving strategy of a channel
(e.g. half/fullstep, fast/slowdecay and so on).
To select the current level is necessary to load a
value into the appropriateDAC. The microproces-
sor must select the channel via A2, A3 and (only
for channel 1 and 2) left or right DAC via D3; the
value of D0,....D2 are loaded in the chosen DAC.
There are two possibilities of changing the value
of a DAC; the first one is to load directly the new
value,the secondone is to cause an increment or
a decrement in a DAC, in this way the burden of
the microprocessor can be partially decreased
generating inc/dec command without calculating
the value.
To increment od decrement a DAC the microproc-
essor must select the channel via A2,A3, left or
right DAC and the operationvia D0 to D3 accord-
ing to truth table in Datas and Address Decoding
(see below). The increment or decrement is done
immediately after the arrive of the command. For
every configuration of the output stages are pos-
sible different type of drivingstrategy explained in
Datas and Address Decoding.
L6280
11/26
相關PDF資料
PDF描述
L6285 3 CHANNELS MULTIPOWER SYSTEM
L6285S 3 CHANNELS MULTIPOWER SYSTEM
L6316 4-CHANNEL LOW POWER PREAMPLIFIER
L634 THREE PHASE MOTOR DRIVER
L6353 Smart Driver for Power MOS & IGBT(用于MOS和絕緣柵雙極晶體管的智能驅動器)
相關代理商/技術參數
參數描述
L6281B12D 制造商:ST MICRO 功能描述:New
L6282-3.2E 制造商:STMicroelectronics 功能描述:L6282-3.2E
L6283-1.2 制造商:STMicroelectronics 功能描述:ELECTRONIC COMPONENT
L6283-1.3 制造商:STMicroelectronics 功能描述:ELECTRONIC COMPONENT
L6285 制造商:STMICROELECTRONICS 制造商全稱:STMicroelectronics 功能描述:3 CHANNELS MULTIPOWER SYSTEM
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*