- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8893FQL (Micrel Inc)IC SWITCH FAST ETH 3PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8893FQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 61/117頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH FAST ETH 3PORT 128PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII，RMII，SNI |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-1603-ND - EVAL KIT EXPERIMENTAL KSZ8893MQL |
| 其它名稱： | 576-1565 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Micrel, Inc.
KSZ8893FQL
October 2007
48
M9999-101607-1.3
Figure 10. KSZ8893FQL EEPROM Configuration Timing Diagram.
The following is a sample procedure for programming the KSZ8893FQL with a pre-configured EEPROM:
1. Connect the KSZ8893FQL to the EEPROM by joining the SCL and SDA signals of the respective devices. For
the KSZ8893FQL, SCL is pin 97 and SDA is pin 98.
2. Enable I
2C master mode by setting the KSZ8893FQL strap-in pins, PS[1:0] (pins 100 and 101, respectively) to
“00”.
3. Check to ensure that the KSZ8893FQL reset signal input, RST_N (pin 67), is properly connected to the external
reset source at the board level.
4. Program the desired configuration data into the EEPROM.
5. Place the EEPROM on the board and power up the board.
6. Assert an active-low reset to the RST_N pin of the KSZ8893FQL. After reset is de-asserted, the KSZ8893FQL
begins reading the configuration data from the EEPROM. The KSZ8893FQL checks that the first byte read from
the EEPROM is “88”. If this value is correct, EEPROM configuration continues. If not, EEPROM configuration
access is denied and all other data sent from the EEPROM is ignored by the KSZ8893FQL. The configuration
access time (tprgm) is less than 15ms.
Note:
For proper operation, check to ensure that the KSZ8893FQL PWRDN input signal (pin 36) is not asserted during
the reset operation. The PWRDN input is active low.
I2C Slave Serial Bus Configuration
In managed mode, the KSZ8893FQL can be configured as an I
2C slave device. In this mode, an I2C master device
(external controller/CPU) has complete programming access to the KSZ8893FQL’s 142 registers. Programming access
includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to the “Static MAC
Table”, “VLAN Table”, “Dynamic MAC Table,” and “MIB Counters.” The tables and counters are indirectly accessed via
registers 121 to 131.
In I
2C slave mode, the KSZ8893FQL operates like other I2C slave devices. Addressing the KSZ8893FQL’s 8-bit
registers is similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of I
2C read/write operations
and related timing information can be found in the AT24C02 Datasheet.
Two fixed 8-bit device addresses are used to address the KSZ8893FQL in I
2C slave mode. One is for read; the other is
for write. The addresses are as follow:
1011_1111 <read>
1011_1110 <write>
The following is a sample procedure for programming the KSZ8893FQL using the I
2C slave serial bus:
1. Enable I
2C slave mode by setting the KSZ8893FQL strap-in pins PS[1:0] (pins 100 and 101, respectively) to
“01”.
2. Power up the board and assert reset to the KSZ8893FQL. After reset, the “Start Switch” bit (register 1 bit [0]) is
set to ‘0’.
3. Configure the desired register settings in the KSZ8893FQL, using the I
2C write operation.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8895MQI | IC ETHERNET SWITCH 5PORT 128PQFP |
| KSZ8895MQ | IC ETHERNET SW 5PORT 128-PQFP |
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8893FQL-EVAL | 功能描述:以太網開發工具 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8893FQL-FX | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893FQLI-FX | 功能描述:以太網 IC 3-Port Ethernet Switch w MII/RMII Interface + 100FX (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL TR | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 100-Ball LFBGA (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。