- 您現在的位置：買賣IC網 > PDF目錄1932 > KSZ8893FQL (Micrel Inc)IC SWITCH FAST ETH 3PORT 128PQFP PDF資料下載
參數資料
| 型號： | KSZ8893FQL |
| 廠商： | Micrel Inc |
| 文件頁數： | 54/117頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC SWITCH FAST ETH 3PORT 128PQFP |
| 標準包裝： | 66 |
| 控制器類型： | 以太網開關控制器 |
| 接口： | MII，RMII，SNI |
| 電源電壓： | 3.1 V ~ 3.5 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 128-BFQFP |
| 供應商設備封裝： | 128-PQFP（14x20） |
| 包裝： | 托盤 |
| 配用： | 576-1603-ND - EVAL KIT EXPERIMENTAL KSZ8893MQL |
| 其它名稱： | 576-1565 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁當前第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁
Micrel, Inc.
KSZ8893FQL
October 2007
41
M9999-101607-1.3
MII Management (MIIM) Interface
The KSZ8893FQL supports the IEEE 802.3 MII Management Interface, also known as the Management Data
Input/Output (MDIO) Interface. This interface allows upper-layer devices to monitor and control the states of the
KSZ8893FQL. An external device with MDC/MDIO capability is used to read the PHY status or configure the PHY
settings. Further details on the MIIM interface can be found in Clause 22.2.4.5 of the IEEE 802.3u Specification.
The MIIM interface consists of the following:
A physical connection that incorporates the data line (MDIO) and the clock line (MDC).
A specific protocol that operates across the aforementioned physical connection that allows an external
controller to communicate with the KSZ8893FQL device.
Access to a set of eight 16-bit registers, consisting of six standard MIIM registers [0:5] and two custom MIIM
registers [29, 31].
The MIIM Interface can operate up to a maximum clock speed of 5 MHz.
The following table depicts the MII Management Interface frame format.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
10
AAAAA
RRRRR
Z0
DDDDDDDD_DDDDDDDD
Z
Write
32 1’s
01
AAAAA
RRRRR
10
DDDDDDDD_DDDDDDDD
Z
Table 12. MII Management Interface Frame Format
Serial Management Interface (SMI)
The SMI is the KSZ8893FQL non-standard MIIM interface that provides access to all KSZ8893FQL configuration
registers. This interface allows an external device to completely monitor and control the states of the KSZ8893FQL.
The SMI interface consists of the following:
A physical connection that incorporates the data line (MDIO) and the clock line (MDC).
A specific protocol that operates across the aforementioned physical connection that allows an external
controller to communicate with the KSZ8893FQL device.
Access to all KSZ8893FQL configuration registers. Register access includes the Global, Port and Advanced
Control Registers 0-141 (0x00 – 0x8D), and indirect access to the standard MIIM registers [0:5] and custom
MIIM registers [29, 31].
The following table depicts the SMI frame format.
Preamble
Start of
Frame
Read/Write
OP Code
PHY
Address
Bits [4:0]
REG
Address
Bits [4:0]
TA
Data
Bits [15:0]
Idle
Read
32 1’s
01
00
1xRRR
RRRRR
Z0
0000_0000_DDDD_DDDD
Z
Write
32 1’s
01
00
0xRRR
RRRRR
10
xxxx_xxxx_DDDD_DDDD
Z
Table 13. Serial Management Interface (SMI) Frame Format
SMI register read access is selected when OP Code is set to “00” and bit 4 of the PHY address is set to ‘1’. SMI register
write access is selected when OP Code is set to “00” and bit 4 of the PHY address is set to ‘0’. PHY address bit[3] is
undefined for SMI register access, and hence, can be set to either ‘0’ or ‘1’ in read/write operations.
To access the KSZ8893FQL registers 0-141 (0x00 – 0x8D), the following applies:
PHYAD[2:0] and REGAD[4:0] are concatenated to form the 8-bit address; that is, {PHYAD[2:0], REGAD[4:0]} =
bits [7:0] of the 8-bit address.
Registers are 8 data bits wide.
–
For read operation, data bits [15:8] are read back as 0’s.
–
For write operation, data bits [15:8] are not defined, and hence can be set to either ‘0’ or ‘1’.
相關PDF資料 |
PDF描述 |
|---|---|
| KSZ8895MQI | IC ETHERNET SWITCH 5PORT 128PQFP |
| KSZ8895MQ | IC ETHERNET SW 5PORT 128-PQFP |
| KSZ8993FL | IC CONV MED 10/100 SGL 128PQFP |
| KSZ8993MLI | IC SWITCH 10/100 3PORT 128-PQFP |
| KSZ8993ML | IC SWITCH 10/100 W/TXRX 128PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| KSZ8893FQL-EVAL | 功能描述:以太網開發工具 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓: |
| KSZ8893FQL-FX | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893FQLI-FX | 功能描述:以太網 IC 3-Port Ethernet Switch w MII/RMII Interface + 100FX (I-Temp, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 128-Ld PQFP(Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
| KSZ8893MBL TR | 功能描述:以太網 IC 2+1 Port 10/100 Switch w/Tranceivers & Frame Buffers, 100-Ball LFBGA (Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。