參數資料
型號： KSZ8873FLL
廠商： Micrel Inc
文件頁數： 53/115頁
文件大小： 0K
描述： IC ETHERNET SW 3PORT 64LQFP
產品培訓模塊： KSZ8873 Ethernet Switches
特色產品： KSZ8873 Ethernet Switch Controller
標準包裝： 160
控制器類型： 以太網開關控制器
接口： MII
電源電壓： 1.8V，2.5V，3.3V
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 64-LQFP
供應商設備封裝： 64-LQFP（10x10）
包裝： 托盤
其它名稱： 576-3631
KSZ8873FLL-ND
Micrel, Inc.
KSZ8873MLL/FLL/RLL
September 20, 2013
42
Revision 1.6
For KSZ8873MLL/FLL/RLL I2C Master configuration, the EEPROM stores the configuration data for Register 0 to
Register 120 (as defined in the KSZ8873MLL/FLL/RLL register map) with the exception of the “Read Only” status
registers. After the de-assertion of reset, the KSZ8873MLL/FLL/RLL sequentially reads in the configuration data for all
control registers, starting from Register 0.
....
RST_N
SCL
SDA
t
prgm<15 ms
Figure 8. EEPROM Configuration Timing Diagram
The following is a sample procedure for programming the KSZ8873MLL/FLL/RLL with a pre-configured EEPROM:
1.
Connect the KSZ8873MLL/FLL/RLL to the EEPROM by joining the SCL and SDA signals of the respective devices.
2.
Enable I
2C master mode by setting the KSZ8873MLL/FLL/RLL strap-in pins, P2LED[1:0] to “00”.
3.
Check to ensure that the KSZ8873MLL/FLL/RLL reset signal input, RSTN, is properly connected to the external reset
source at the board level.
4.
Program the desired configuration data into the EEPROM.
5.
Place the EEPROM on the board and power up the board.
6.
Assert an active-low reset to the RSTN pin of the KSZ8873MLL/FLL/RLL. After reset is de-asserted, the
KSZ8873MLL/FLL/RLL begins reading the configuration data from the EEPROM. The KSZ8873MLL/FLL/RLL checks
that the first byte read from the EEPROM is “88”. If this value is correct, EEPROM configuration continues. If not,
EEPROM configuration access is denied and all other data sent from the EEPROM is ignored by the
KSZ8873MLL/FLL/RLL.
Note: For proper operation, check to ensure that the KSZ8873MLL/FLL/RLL PWRDN input signal is not asserted during
the reset operation. The PWRDN input is active low.
I
2C Slave Serial Bus Configuration
In managed mode, the KSZ8873MLL/FLL/RLL can be configured as an I2C slave device. In this mode, an I2C master
device (external controller/CPU) has complete programming access to the KSZ8873MLL/FLL/RLL’s 198 registers.
Programming access includes the Global Registers, Port Registers, Advanced Control Registers and indirect access to
the “Static MAC Table”, “VLAN Table”, “Dynamic MAC Table,” and “MIB Counters.” The tables and counters are indirectly
accessed via registers 121 to 131.
In
I
2C slave mode, the KSZ8873MLL/FLL/RLL operates like other I2C slave devices. Addressing the
KSZ8873MLL/FLL/RLL’s 8-bit registers is similar to addressing Atmel’s AT24C02 EEPROM’s memory locations. Details of
I
2C read/write operations and related timing information can be found in the AT24C02 Datasheet.
相關PDF資料
PDF描述
VI-B6J-IW-F1 CONVERTER MOD DC/DC 36V 100W
VI-B6H-IW-F2 CONVERTER MOD DC/DC 52V 100W
VI-B6F-IX-F4 CONVERTER MOD DC/DC 72V 75W
VI-B6F-IW-F2 CONVERTER MOD DC/DC 72V 100W
VI-B6D-IX-F1 CONVERTER MOD DC/DC 85V 75W
相關代理商/技術參數
參數描述
KSZ8873FLL-EVAL 功能描述:以太網開發工具 3-Port Fast Ethernet Switch with 2x FX Ports - Evaluation Board RoHS:否 制造商:Micrel 產品:Evaluation Boards 類型:Ethernet Transceivers 工具用于評估:KSZ8873RLL 接口類型:RMII 工作電源電壓:
KSZ8873FLLI 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 2x FX Ports (Industrial Grade) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL 功能描述:以太網 IC 3-Port Fast Ethernet Switch with 1x MII Interface - Lead Free RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL AM 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
KSZ8873MLL AM TR 功能描述:以太網 IC 3-Port 10/100 Ethernet Switch with 1x MII Interface (Automotive Grade, Lead Free) RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*