- 您現在的位置：買賣IC網 > PDF目錄374297 > K9K8G08U1M (SAMSUNG SEMICONDUCTOR CO. LTD.) 512M x 8 Bits / 1G x 8 Bits NAND Flash Memory PDF資料下載
參數資料
| 型號： | K9K8G08U1M |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | 512M x 8 Bits / 1G x 8 Bits NAND Flash Memory |
| 中文描述： | 512M x 8位/ 1克× 8位NAND閃存 |
| 文件頁數： | 33/41頁 |
| 文件大?。?/td> | 1076K |
| 代理商： | K9K8G08U1M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁當前第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
FLASH MEMORY
33
Advance
K9F4G08U0M
K9K8G08U1M
Figure 9. Random Data Input In a Page
80h
R/B
Address & Data Input
I/O
0
Pass
10h
70h
Fail
t
PROG
85h
Address & Data Input
I/Ox
Col. Add.1,2 & Row Add1,2,3
Data
Col. Add.1,2
Data
"0"
"1"
Copy-Back Program
The Copy-Back program is configured to quickly and efficiently rewrite data stored in one page without utilizing an external memory.
Since the time-consuming cycles of serial access and re-loading cycles are removed, the system performance is improved. The ben-
efit is especially obvious when a portion of a block is updated and the rest of the block also need to be copied to the newly assigned
free block. The operation for performing a copy-back program is a sequential execution of page-read without serial access and copy-
ing-program with the address of destination page. A read operation with "35h" command and the address of the source page moves
the whole 2,112-byte data into the internal data buffer. As soon as the device returns to Ready state, Page-Copy Data-input com-
mand (85h) with the address cycles of destination page followed may be written. The Program Confirm command (10h) is required to
actually begin the programming operation. During tPROG, the device executes EDC of itself. Once the program process starts, the
Read Status Register command (70h) or Read EDC Status command (7Bh) may be entered to read the status register. The system
controller can detect the completion of a program cycle by monitoring the R/B output, or the Status bit(I/O 6) of the Status Register.
When the Copy-Back Program is complete, the Write Status Bit(I/O 0) and EDC Status Bits (I/O 1 ~ I/O 4) may be checked(Figure 10
& Figure 11& Figure 12). The internal write verification detects only errors for "1"s that are not successfully programmed to "0"s and
the internal EDC checks whether there is only 1-bit error for each 528-byte plane of the source page. More than 2-bit error detection
is not available for each 528-byte plane. The command register remains in Read Status command mode or Read EDC Status com-
mand mode until another valid command is written to the command register.
During copy-back program, data modification is possible using random data input command (85h) as shown in Figure11. But EDC
status Bits are not available during copy back for some bits or bytes modified by Random Data Input operation.
However, in case of the 528 byte plane unit modification, EDC status bits are abailable.
Figure 10. Page Copy-Back program Operation
00h
R/B
Add.(5Cycles)
I/O
0
Pass
85h
Col. Add.1,2 & Row Add.1,2,3
70h
Fail
t
PROG
Add.(5Cycles)
t
R
Source Address
Destination Address
35h
10h
I/Ox
Col. Add.1,2 & Row Add.1,2,3
Figure 11. Page Copy-Back program Operation with Random Data Input
00h
R/B
Add.(5Cycles)
85h
70h
t
PROG
Add.(5Cycles)
t
R
Source Address
Destination Address
Data
35h
10h
85h
Data
Add.(2Cycles)
There is no limitation for the number of repetition.
I/Ox
Col. Add.1,2 & Row Add.1,2,3
Col. Add.1,2 & Row Add.1,2,3
Col. Add.1,2
Note:
1. For EDC operation, only one time random data input is possible at the same address.
Note
:
1. Copy-Back Program operation is allowed only within the same memory plane.
2. On the same plane, It’s prohibited to operate copy-back program from an odd address page(source page) to an even
address page(target page) or from an even address page(source page) to an odd address page(target page).
Therefore, the copy-back program is permitted just between odd address pages or even address pages.
相關PDF資料 |
PDF描述 |
|---|---|
| K9F5608Q0C | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608Q0C-D | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608Q0C-H | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608U0C | 512Mb/256Mb 1.8V NAND Flash Errata |
| K9F5608U0C-D | 512Mb/256Mb 1.8V NAND Flash Errata |
相關代理商/技術參數 |
參數描述 |
|---|---|
| K9K8G08UOA | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:1G x 8 Bit / 2G x 8 Bit / 4G x 8 Bit NAND Flash Memory |
| K9KAG08U0MPCB00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:sheet of this product is either in preparation or is not effective yet. For more details about product specifications or technical files, please inquire through Contact us |
| K9KAG08U0M-PCB0000 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:sheet of this product is either in preparation or is not effective yet. For more details about product specifications or technical files, please inquire through Contact us |
| K9KAG08U0MPCB0T | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:sheet of this product is either in preparation or is not effective yet. For more details about product specifications or technical files, please inquire through Contact us |
| K9KAG08U0MPCK00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:sheet of this product is either in preparation or is not effective yet. For more details about product specifications or technical files, please inquire through Contact us |
發布緊急采購，3分鐘左右您將得到回復。