參數資料
型號: ISP1583BS,551
廠商: ST-ERICSSON
元件分類: 總線控制器
英文描述: UNIVERSAL SERIAL BUS CONTROLLER, PQCC64
封裝: 9 X 9 MM, 0.85 MM HEIGHT, LEAD FREE, PLASTIC, MO-220, SOT-804-1, HVQFN-64
文件頁數: 79/100頁
文件大小: 508K
代理商: ISP1583BS,551
ISP1583_7
NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 07 — 22 September 2008
7 of 99
NXP Semiconductors
ISP1583
Hi-Speed USB peripheral controller
DACK
10
F1
E2
I/O
DMA acknowledge input or output (programmable
polarity); the signal direction depends on bit MASTER in
register DMA Hardware (see Table 59):
Input: DMA slave mode if bit MASTER = 0
Output: DMA master mode if bit MASTER = 1
When not in use, in the default setting, this pin must be
connected to VCC(I/O) through a 10 k resistor.
bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant
DIOR
11
G2
E3
I/O
DMA read strobe input or output (programmable polarity);
the signal direction depends on bit MASTER in register
DMA Hardware (see Table 59):
Input: DMA slave mode if bit MASTER = 0
Output: DMA master mode if bit MASTER = 1
When not in use, in the default setting, this pin must be
connected to VCC(I/O) through a 10 k resistor.
bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant
DIOW
12
G1
F1
I/O
DMA write strobe input or output (programmable polarity);
the signal direction depends on bit MASTER in register
DMA Hardware (see Table 59):
Input: DMA slave mode if bit MASTER = 0
Output: DMA master mode if bit MASTER = 1
When not in use, in the default setting, this pin must be
connected to VCC(I/O) through a 10 k resistor.
bidirectional pad; 4 ns slew-rate control; TTL; 5 V tolerant
DGND
13
H2
F2
-
digital ground
INTRQ
14
H1
G2
I
interrupt request input; from the ATA/ATAPI peripheral; use
a 10 k
resistor to pull down
input pad; TTL; 5 V tolerant
READY/
IORDY
15
J1
G1
I/O
Signal ready output — Used in generic processor mode:
LOW: the ISP1583 is processing a previous command
or data and is not ready for the next command or data
transfer
HIGH: the ISP1583 is ready for the next
microprocessor read or write
I/O ready input — Used in split bus mode to access
ATA/ATAPI peripherals (PIO mode only)
bidirectional pad; 10 ns slew-rate control; TTL; 5 V tolerant
INT
16
K1
H1
O
interrupt output; programmable polarity (active HIGH or
LOW) and signaling (edge or level triggered)
CMOS output; 8 mA drive
DA2[3]
17
J2
H2
O
address output to select the Task File register of an
ATA/ATAPI device; see Table 61
CMOS output; 8 mA drive
CS_N
18
K2
E4
I
chip selection input
input pad; TTL; 5 V tolerant
Table 3.
Pin description …continued
Symbol[1]
Pin
Type[2] Description
ISP1583BS ISP1583ET;
ISP1583ET2
ISP1583ET1
相關PDF資料
PDF描述
ISP1583ET2 UNIVERSAL SERIAL BUS CONTROLLER, PBGA64
ISP1761ET,518 UNIVERSAL SERIAL BUS CONTROLLER, PBGA128
ISP1761BE,518 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
ISP1761BE,551 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
ISP1761BE,518 UNIVERSAL SERIAL BUS CONTROLLER, PQFP128
相關代理商/技術參數
參數描述
ISP1583BSGA 功能描述:IC USB CTRL HI-SPEED 64HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ISP1583BS-S 功能描述:USB 接口集成電路 HI-SPEED USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1583BS-T 功能描述:USB 接口集成電路 USB PERIPH CNTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1583BSUM 功能描述:IC USB PERIPH CONTROLLER 64HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ISP1583ET 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB peripheral controller