- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1301 (NXP Semiconductors N.V.) Universal Serial Bus On-The-Go transceiver PDF資料下載
參數資料
| 型號： | ISP1301 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Universal Serial Bus On-The-Go transceiver |
| 中文描述： | 通用串行總線在- The - Go的收發器 |
| 文件頁數： | 23/46頁 |
| 文件大?。?/td> | 245K |
| 代理商： | ISP1301 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁當前第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁
Philips Semiconductors
ISP1301
USB OTG transceiver
Product data
Rev. 01 — 14 April 2004
23 of 46
9397 750 11355
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
The Interrupt Latch register bit is cleared by writing logic 1 to its clear address.
11.3 Autoconnect
The Host Negotiation Protocol (HNP) in the OTG supplement specifies the following
sequence of events to transfer the role of the host from the A-device to the B-device:
1. The A-device puts the bus in the suspend state
2. The B-device simulates a disconnect by deasserting its DP pull-up
3. The A-device detects SE0 on the bus, and asserts its DP pull-up
4. The B-device detects that the DP line is HIGH, and takes the role of the host.
The OTG supplement specifies that the time between the B-device deasserting its DP
pull-up and the A-device asserting its pull-up must be less than 3 ms. For an A-device
with a slow interrupt response time, 3 ms may not be enough time to write an I
2
C-bus
command to the ISP1301 to assert the DP pull-up. An alternative method is for the
A-device transceiver to automatically assert the DP pull-up after detecting an SE0
from the B-device.
The sequence of events is as follows:
After finishing data transfers between the A-device and the B-device and before
suspending the bus, the A-device sends SOFs. The B-device receives these SOFs,
and does not transmit any packet back to the A-device. During this time, the A-device
sets the BDIS_ACON_EN bit in the ISP1301. This enables the ISP1301 to look for
SE0 whenever the A-device is not transmitting (that is, whenever the OE_N/INT_N
pin of the ISP1301 is not asserted). After the BDIS_ACON_EN bit is set, the A-device
stops transmitting SOFs and allows the bus to go to the idle state. If the B-device
disconnects, the bus goes to SE0, and the ISP1301 logic automatically turns on the
A-device pull-up.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1301BS | Universal Serial Bus On-The-Go transceiver |
| ISP1362 | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362BD | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1362EE | Single-chip Universal Serial Bus On-The-Go controller |
| ISP1501 | Hi-Speed Universal Serial Bus peripheral transceiver |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1301BS | 功能描述:IC USB OTG TRANSCEIVER 24-HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:1,000 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:16-SOIC 包裝:帶卷 (TR) |
| ISP1301BS,115 | 功能描述:射頻收發器 USB OTG TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,118 | 功能描述:射頻收發器 DO NOT USE ORDER -G OR -S PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,151 | 功能描述:射頻收發器 USB OTG TRANSCEIVER RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
| ISP1301BS,157 | 功能描述:射頻收發器 DO NOT USE ORDER -G OR -S PART RoHS:否 制造商:Atmel 頻率范圍:2322 MHz to 2527 MHz 最大數據速率:2000 Kbps 調制格式:OQPSK 輸出功率:4 dBm 類型: 工作電源電壓:1.8 V to 3.6 V 最大工作溫度:+ 85 C 接口類型:SPI 封裝 / 箱體:QFN-32 封裝:Tray |
發布緊急采購，3分鐘左右您將得到回復。