參數資料
型號: ISP1161
廠商: NXP Semiconductors N.V.
英文描述: Full-speed Universal Serial Bus single-chip host and device controller
中文描述: 全速通用串行總線的單芯片主機和設備控制器
文件頁數: 26/127頁
文件大?。?/td> 2762K
代理商: ISP1161
Philips Semiconductors
ISP1161
Full-speed USB single-chip host and device controller
Product data
Rev. 01 — 3 July 2001
26 of 130
9397 750 08313
Philips Electronics N.V. 2001. All rights reserved.
Table 5:
Symbol
ActualBytes[9:0]
CompletionCode[3:0]
Philips Transfer Descriptor (PTD): bit description
Access
R/W
Contains the number of bytes that were transferred for this PTD
R/W
0000
NoError
Description
General TD or isochronous data packet processing
completed with no detected errors.
Last data packet from endpoint contained a CRC error.
Last data packet from endpoint contained a bit stuffing
violation.
Last packet from endpoint had data toggle PID that did
not match the expected value.
TD was moved to the Done queue because the
endpoint returned a STALL PID.
Device did not respond to token (IN) or did not provide a
handshake (OUT).
Check bits on PID from endpoint failed on data PID (IN)
or handshake (OUT)
Received PID was not valid when encountered or PID
value is not defined.
The amount of data returned by the endpoint exceeded
either the size of the maximum data packet allowed
from the endpoint (found in MaximumPacketSize field of
ED) or the remaining buffer size.
The endpoint returned is less than MaximumPacketSize
and that amount was not sufficient to fill the specified
buffer.
-
-
During an IN, the HC received data from an endpoint
faster than it could be written to system memory.
During an OUT, the HC could not retrieve data from the
system memory fast enough to keep up with the USB
data rate.
0001
0010
CRC
BitStuffing
0011
DataToggleMismatch
0100
Stall
0101
DeviceNotResponding
0110
PIDCheckFailure
0111
UnexpectedPID
1000
DataOverrun
1001
DataUnderrun
1010
1011
1100
reserved
reserved
BufferOverrun
1101
BufferUnderrun
Active
R/W
Set to logic 1 by firmware to enable the execution of transactions by the HC. When the
transaction associated with this descriptor is completed, the HC sets this bit to logic 0,
indicating that a transaction for this element should not be executed when it is next
encountered in the schedule.
Used to generate or compare the data PID value (DATA0 or DATA1). It is updated after
each successful transmission or reception of a data packet.
The maximum number of bytes that can be sent to or received from the endpoint in a
single data packet.
USB address of the endpoint within the function.
Last PTD of a list (ITL or ATL). A logic 1 indicates that the PTD is the last PTD.
Speed of the endpoint:
S = 0 —
full speed
S = 1 —
low speed
Toggle
R/W
MaxPacketSize[9:0]
R
EndpointNumber[3:0]
Last(PTD)
(Low)Speed
R
R
R
相關PDF資料
PDF描述
ISP1161A1 Universal Serial Bus single-chip host and device controller
ISP1161A1BD Universal Serial Bus single-chip host and device controller
ISP1161A1BM Universal Serial Bus single-chip host and device controller
ISP1161BD Full-speed Universal Serial Bus single-chip host and device controller
ISP1161BM Full-speed Universal Serial Bus single-chip host and device controller
相關代理商/技術參數
參數描述
ISP1161A 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Full-speed Universal Serial Bus single-chip host and device controller
ISP1161A1 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus single-chip host and device controller
ISP1161A1BD 功能描述:IC USB HOST/DEVICE CTRLR 64-LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN(6x6) 包裝:* 其它名稱:Q6396337A
ISP1161A1BD,118 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20
ISP1161A1BD,151 功能描述:USB 接口集成電路 USB1.1 HOST &DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20