20 FN7575.5 September 5, 2012 BETA Register (BETA) The BETA register has special Write properties. Only the TSE, BTSE and BTSR bits " />
參數資料
型號: ISL12022MAIBZ
廠商: Intersil
文件頁數: 13/31頁
文件大?。?/td> 0K
描述: IC RTC/CALENDAR TEMP SNSR 20SOIC
產品培訓模塊: Solutions for Industrial Control Applications
標準包裝: 38
類型: 時鐘/日歷
特點: 警報器,夏令時,閏年,SRAM
存儲容量: 128B
時間格式: HH:MM:SS(12/24 小時)
數據格式: YY-MM-DD-dd
接口: I²C,2 線串口
電源電壓: 2.7 V ~ 5.5 V
電壓 - 電源,電池: 1.8 V ~ 5.5 V
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 20-SOIC(0.295",7.50mm 寬)
供應商設備封裝: 20-SOIC
包裝: 管件
ISL12022MA
20
FN7575.5
September 5, 2012
BETA Register (BETA)
The BETA register has special Write properties. Only the TSE,
BTSE and BTSR bits can be written; the BETA bits are READ-ONLY.
A write to both bytes in this register will only change the 3 MSB’s
(TSE, BTSE, BTSR), and the 5 LSB’s will remain the same as set
at the factory.
TEMPERATURE SENSOR ENABLED BIT (TSE)
This bit enables the Temperature Sensing operation, including the
temperature sensor, A/D converter and FATR/FDTR register
adjustment. The default mode after power-up is disabled: (TSE = 0).
To enable the operation, TSE should be set to 1. (TSE = 1). When
temp sense is disabled, the initial values for IATR and IDTR registers
are used for frequency control.
When TSE is set to 1, the temperature conversion cycle begins and
will end when two temperature conversions are completed. The
average of the two conversions is in the TEMP registers.
TEMP SENSOR CONVERSION IN BATTERY MODE BIT
(BTSE)
This bit enables the Temperature Sensing and Correction in battery
mode. BTSE = 0 (default) no conversion, Temp Sensing or
Compensation in battery mode. BTSE = 1 indicates Temp Sensing
and Compensation enabled in battery mode. The BTSE is disabled
when the battery voltage is lower than 2.7V. No temperature
compensation will take place with VBAT<2.7V.
FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT (BTSR)
This bit controls the frequency of Temp Sensing and Correction.
BTSR = 0 default mode is every 10 minutes, BTSR = 1 is every
1.0 minute. Note that BTSE has to be enabled in both cases. See
Table 16.
The temperature measurement conversion time is the same for
battery mode as for VDD mode, approximately 22ms. The battery
mode current will increase during this conversion time to
typically 68A. The average increase in battery current is much
lower than this due to the small duty cycle of the ON-time versus
OFF-time for the conversion.
To figure the average increase in battery current, we take the
change in current times the duty cycle. For the 1 minute
temperature period, the average current is expressed in
Equation 1:
For the 10 minute temperature period the average current is
expressed in Equation 2:
If the application has a stable temperature environment that
doesn’t change quickly, the 10 minute option will work well and
the backup battery lifetime impact is minimized. If quick
temperature variations are expected (multiple cycles of more
than 10° within an hour), then the 1 minute option should be
considered and the slightly higher battery current figured into
overall battery life.
GAIN FACTOR OF AT BIT (BETA<4:0>)
Beta is specified to take care of the Cm variations of the crystal.
Most crystals specify Cm around 2.2fF. For example, if Cm > 2.2fF,
the actual AT steps may reduce from 1ppm/step to approximately
0.80ppm/step. Beta is then used to adjust for this variation and
restore the step size to 1ppm/step.
BETA values are limited in the range from 01000 to 11111, as
shown in Table 17. To use Table 17, the device is tested at two AT
settings as follows:
BETA VALUES = (AT(max) - AT (min))/63, where:
AT(max) = FOUT in ppm (at AT = 00H) and
AT(min) = FOUT in ppm (at AT = 3FH).
The BETA VALUES result is indexed in the right hand column and
the resulting Beta factor (for the register) is in the same row in
the left column.
The ISL12022MA has a preset BETA value corresponding to the
crystal in the module. This value is recalled on initial power-up
and is preset in device production. It is READ ONLY and cannot
be overwritten by the user.
TABLE 15.
ADDR
7
6
5
4
321
0
0Dh
TSE BTSE BTSR BETA4 BETA3 BETA2 BETA1 BETA0
TABLE 16. FREQUENCY OF TEMPERATURE SENSING AND
CORRECTION BIT
BTSE
BTSR
TC PERIOD IN
BATTERY MODE
00
Off
01
Off
10
10 Minutes
11
1 Minute
TABLE 17. BETA VALUES
BETA<4:0>
AT STEP ADJUSTMENT
01000
0.5000
00111
0.5625
00110
0.6250
00101
0.6875
00100
0.7500
00011
0.8125
00010
0.8750
00001
0.9375
00000
1.0000
10000
1.0625
10001
1.1250
10010
1.1875
ΔI
BAT
0.022s
60s
------------------
=
68
μA 250nA
=
×
(EQ. 1)
ΔI
BAT
0.022s
600s
------------------
=
68
μA 25nA
=
×
(EQ. 2)
相關PDF資料
PDF描述
ISL12022MIBZ-T7A IC RTC/CALENDAR TEMP SNSR 20SOIC
ISL12022MIBZR5421 IC RTC/CALENDAR TEMP SNSR 20SOIC
ISL12023IVZ IC RTC/CLDR TEMP SNSR 14-TSSOP
ISL12024IRTCZ IC RTC/CALENDER 64BIT 8-TDFN
ISL12024IVZ IC RTC/CALENDAR EEPROM 8-TSSOP
相關代理商/技術參數
參數描述
ISL12022MAIBZ-T 功能描述:實時時鐘 REAL TIME CLK ENHANC CD ESD & MOISTURESIS RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12022M-EVAL 制造商:Intersil Corporation 功能描述:Low Power RTC with Battery Backed SRAM, Integrated 5ppm Temperature Compensation, and Auto Daylight Saving
ISL12022MIBZ 功能描述:實時時鐘 REAL TIME CLK & TEMP COMPENSATED CRYSTAL RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube
ISL12022MIBZ-EVAL 功能描述:電源管理IC開發工具 ISL12022MIBZ-EVAL DEMO BRD RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V
ISL12022MIBZR5421 功能描述:實時時鐘 REAL TIME CLK W/MFK IMPROVED ESD AIR RoHS:否 制造商:Microchip Technology 功能:Clock, Calendar. Alarm RTC 總線接口:I2C 日期格式:DW:DM:M:Y 時間格式:HH:MM:SS RTC 存儲容量:64 B 電源電壓-最大:5.5 V 電源電壓-最小:1.8 V 最大工作溫度:+ 85 C 最小工作溫度: 安裝風格:Through Hole 封裝 / 箱體:PDIP-8 封裝:Tube