- 您現在的位置：買賣IC網 > PDF目錄9576 > IDT82V3011PVG8 (IDT, Integrated Device Technology Inc)IC PLL WAN T1/E1/OC3 SGL 56-SSOP PDF資料下載
參數資料
| 型號： | IDT82V3011PVG8 |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 8/31頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC PLL WAN T1/E1/OC3 SGL 56-SSOP |
| 標準包裝： | 1,000 |
| 類型： | 時鐘/頻率發生器 |
| PLL： | 是 |
| 主要目的： | 電信 |
| 輸入： | 時鐘 |
| 輸出： | CMOS，LVDS，TTL |
| 電路數： | 1 |
| 比率 - 輸入:輸出： | 1:12 |
| 差分 - 輸入:輸出： | 無/是 |
| 頻率 - 最大： | 32.768MHz |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 56-BSSOP（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 56-SSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | 82V3011PVG8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁
Measures of Performance
16
May 24, 2006
IDT82V3011
T1/E1/OC3 WAN PLL WITH SINGLE REFERENCE INPUT
3
MEASURES
OF
PERFOR-
MANCE
The following are some synchronizer performance indicators and
their corresponding definitions.
3.1
INTRINSIC JITTER
Intrinsic jitter is the jitter produced by the synchronizing circuit and is
measured at its output. It is measured by applying a reference signal
with no jitter to the input of the device, and measuring its output jitter.
Intrinsic jitter may also be measured when the device is in a non-
synchronizing mode, such as free running or holdover, by measuring the
output jitter of the device. Intrinsic jitter is usually measured with various
band limiting filters depending on the applicable standards. For the
IDT82V3011, the intrinsic Jitter is limited to less than 0.02 UI on the
2.048 MHz and 1.544 MHz clocks.
3.2
JITTER TOLERANCE
Jitter tolerance is a measure of the ability of a DPLL to operate
properly (i.e., remain in lock and or regain lock in the presence of large
jitter magnitudes at various jitter frequencies) when jitter is applied to its
reference. The applied jitter magnitude and jitter frequency depends on
the applicable standards.
3.3
JITTER TRANSFER
Jitter transfer or jitter attenuation refers to the magnitude of jitter at
the output of a device for a given amount of jitter at the input of the
device. Input jitter is applied at various amplitudes and frequencies, and
output jitter is measured with various filters depending on the applicable
standards.
For the IDT82V3011, two internal elements determine the jitter
attenuation. This includes the internal 2.1 Hz low pass loop filter and the
phase slope limiter. The phase slope limiter limits the output phase slope
to 5 ns per 125 s. Therefore, if the input signal exceeds this rate, such
as for very large amplitude, low frequency input jitter, the maximum
output phase slope will be limited (i.e., attenuated) to 5 ns per 125 s.
The IDT82V3011 has 16 outputs with 4 possible input frequencies for
a total of 64 possible jitter transfer functions. Since all outputs are
derived from the same signal, the jitter transfer values for the four cases,
8 kHz to 8 kHz, 1.544 MHz to 1.544 MHz, 2.048 MHz to 2.048 MHz and
19.44 MHz to 19.44 MHz can be applied to all outputs.
It should be noted that 1 UI at 1.544 MHz is 644 ns, which is not
equal to 1 UI at 2.048 MHz, which is 488 ns. Consequently, a transfer
value using different input and output frequencies must be calculated in
common units (e.g., seconds).
Using the above method, the jitter attenuation can be calculated for
all combinations of inputs and outputs based on the four jitter transfer
functions provided. Note that the resulting jitter transfer functions for all
combinations of inputs (8 kHz, 1.544 MHz, 2.048 MHz, 19.44 MHz) and
outputs (8 kHz, 1.544 MHz, 3.088 MHz, 6.312 MHz, 2.048 MHz, 4.096
MHz, 8.192 MHz, 16.384 MHz, 19.44 MHz, 32.768 MHz) for a given
input signal (jitter frequency and jitter amplitude) are the same.
Since intrinsic jitter is always present, jitter attenuation will appear to
be lower for small input jitter signals than for large ones. Consequently,
accurate jitter transfer function measurements are usually made with
large input jitter signals (e.g., 75% of the specified maximum jitter
tolerance).
3.4
FREQUENCY ACCURACY
Frequency accuracy is defined as the absolute tolerance of an output
clock signal when it is not locked to an external reference, but is
operating in a free running mode. For the IDT82V3011, the Freerun
accuracy is equal to the Master Clock (OSCi) accuracy.
3.5
HOLDOVER ACCURACY
Holdover accuracy is defined as the absolute tolerance of an output
clock signal, when it is not locked to an external reference signal, but is
operating using storage techniques. For the IDT82V3011, the storage
value is determined while the device is in Normal mode and locked to an
external reference signal.
The absolute Master Clock (OSCi) accuracy of the IDT82V3011 does
not affect Holdover accuracy, but the change in OSCi accuracy while in
Holdover mode does.
3.6
CAPTURE RANGE
Also referred to as pull-in range. This is the input frequency range
over which the synchronizer must be able to pull into synchronization.
The IDT82V3011 capture range is equal to ±230 ppm minus the
accuracy of the master clock (OSCi). For example, a 32 ppm master
clock results in a capture range of 198 ppm.
The Telcordia GR-1244-CORE standard, recommends that the DPLL
should be able to reject references that are off the nominal frequency by
more than ±12 ppm. The IDT82V3011 provides a MON_out pin to
indicate whether the reference input Fref is within ±12 ppm of the
nominal frequency.
3.7
LOCK RANGE
This is the input frequency range over which the synchronizer must
be able to maintain synchronization. The lock range is equal to the
capture range for the IDT82V3011.
3.8
PHASE SLOPE
Phase slope is measured in seconds per second and is the rate at
which a given signal changes phase with respect to an ideal signal. The
given signal is typically the output signal. The ideal signal is of constant
frequency and is nominally equal to the value of the final output signal or
final input signal.
3.9
TIME INTERVAL ERROR (TIE)
TIE is the time delay between a given timing signal and an ideal
timing signal.
3.10
MAXIMUM TIME INTERVAL ERROR (MTIE)
MTIE is the maximum peak to peak delay between a given timing
signal and an ideal timing signal within a particular observation period.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BN4-MY-S | CONVERTER MOD DC/DC 48V 50W |
| VE-BN3-MY-S | CONVERTER MOD DC/DC 24V 50W |
| VE-B2H-MW-F2 | CONVERTER MOD DC/DC 52V 100W |
| SI5319C-C-GM | IC CLOCK MULT/ATTENUATOR 36QFN |
| VE-B24-MW-F4 | CONVERTER MOD DC/DC 48V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82V3012 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:T1/E1/OC3 WAN PLL WITH DUAL REFERENCE INPUTS |
| IDT82V3012PV | 制造商:Integrated Device Technology Inc 功能描述: |
| IDT82V3012PVG | 功能描述:IC PLL WAN T1/E1/OC3 DUAL 56SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1 系列:- 類型:時鐘/頻率發生器，多路復用器 PLL:是 主要目的:存儲器，RDRAM 輸入:晶體 輸出:LVCMOS 電路數:1 比率 - 輸入:輸出:1:2 差分 - 輸入:輸出:無/是 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:0°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:Digi-Reel® 其它名稱:296-6719-6 |
| IDT82V3012PVG8 | 功能描述:IC PLL WAN T1/E1/OC3 DUAL 56SSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 專用 系列:- 標準包裝:1,500 系列:- 類型:時鐘緩沖器/驅動器 PLL:是 主要目的:- 輸入:- 輸出:- 電路數:- 比率 - 輸入:輸出:- 差分 - 輸入:輸出:- 頻率 - 最大:- 電源電壓:3.3V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:帶卷 (TR) 其它名稱:93786AFT |
| IDT82V3155 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:ENHANCED T1/E1/OC3 WAN PLL WITH DUAL REFERENCE INPUTS |
發布緊急采購，3分鐘左右您將得到回復。