參數資料
型號： IDT82P2821BH
廠商： IDT, Integrated Device Technology Inc
文件頁數： 79/151頁
文件大?。?/td> 0K
描述： IC LIU T1/J1/E1 21+1CH 640-PBGA
標準包裝： 5
功能： 線路接口單元（LIU）
接口： E1，J1，T1
電路數： 1
電源電壓： 1.8V, 3.3V
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 640-BGA 裸露焊盤
供應商設備封裝： 640-PBGA-EP（31x31）
包裝： 托盤
包括： 缺陷和警報檢測，驅動器過流檢測和保護，LLOS 檢測，PRBSARB / IB 檢測和生成
其它名稱： 82P2821BH
IDT82P2821
21(+1) CHANNEL HIGH-DENSITY T1/E1/J1 LINE INTERFACE UNIT
Functional Description
33
February 6, 2009
3.2.3
SLICER
The Slicer is used to generate a standard amplitude mark or a space
according to the amplitude of the input signals. The input signal is sliced
at 50% of the peak value.
3.2.4
RX CLOCK & DATA RECOVERY
The Rx Clock & Data Recovery is used to recover the clock signal
from the received data. It is accomplished by an integrated Digital Phase
Locked Loop (DPLL). The recovered clock tracks the jitter in the data
output from the Slicer and keeps the phase relationship between data
and clock during the absence of the incoming pulse.
Note that the IDT82P2821 also provides programmable REFA and
REFB pins to output any of the 22 recovered line clocks. Refer to
3.2.5
DECODER
The Decoder is used only when the receive system interface is in
Single Rail NRZ Format mode. When the receive system interface is in
other modes, the Decoder is bypassed automatically. (Refer to
Section 3.2.6 Receive System Interface for the description of the receive
system interface).
In T1/J1 mode, the received signal is decoded by AMI or B8ZS line
code rule. In E1 mode, the received signal is decoded by AMI or HDB3
line code rule. The line code rule is selected by the R_CODE bit (b2,
3.2.6
RECEIVE SYSTEM INTERFACE
The received data can be output to the system side in four modes:
Single Rail NRZ Format mode, Dual Rail NRZ Format mode, Dual Rail
RZ Format mode and Dual Rail Sliced mode, as selected by the
R_MD[1:0] bits (b1~0, RCF1).
If data is output on RDn in NRZ format and the recovered clock is
output on RCLKn, the receive system interface is in Single Rail NRZ
Format mode. In this mode, the data is decoded and updated on the
active edge of RCLKn. RCLKn outputs a 1.544 MHz (in T1/J1 mode) or
2.048 MHz (in E1 mode) clock. The Receive Multiplex Function (RMFn)
signal is updated on the active edge of RCLKn and can be selected to
indicate PRBS/ARB, LAIS, LEXZ, LBPV, LEXZ + LBPV, LLOS, output
recovered clock (RCLK) or XOR output of positive and negative sliced
data. Refer to Section 3.5.7.1 RMFn Indication for the description of
RMFn.
If data is output on RDPn and RDNn in NRZ format and the recov-
ered clock is output on RCLKn, the receive system interface is in Dual
Rail NRZ Format mode. In this mode, the data is un-decoded and
updated on the active edge of RCLKn. RCLKn outputs a 1.544 MHz (in
T1/J1 mode) or 2.048 MHz (in E1 mode) clock.
If data is output on RDPn and RDNn in RZ format and the recovered
clock is output on RCLKn, the receive system interface is in Dual Rail
RZ Format mode. In this mode, the data is un-decoded and updated on
the active edge of RCLKn. RCLKn outputs a 1.544 MHz (in T1/J1 mode)
or 2.048 MHz (in E1 mode) clock.
If data is output on RDPn and RDNn in RZ format directly after
passing through the Slicer, the receive system interface is in Dual Rail
Sliced mode. In this mode, the data is raw sliced and un-decoded.
RMFn can be selected to indicate PRBS/ARB, LAIS, LEXZ, LBPV, LEXZ
+ LBPV, LLOS, output recovered clock (RCLK) or XOR output of positive
and negative sliced data. Refer to Chapter 3.5.7.1 RMFn Indication for
the description of RMFn.
Table-3 summarizes the multiplex pin used in different receive
system interface.
Table-3 Multiplex Pin Used in Receive System Interface
Receive System
Interface
Multiplex Pin Used On Receive System
Interface
RDn / RDPn
RDNn / RMFn
RCLKn /
RMFn
Single Rail NRZ Format
RDn 1
RMFn 2
RCLKn 3
Dual Rail NRZ Format
RDPn 1
RDNn 1
RCLKn 3
Dual Rail RZ Format
RDPn 1
RDNn 1
RCLKn 3
Dual Rail Sliced
RDPn 1
RDNn 1
RMFn 2
Note:
1. The active level on RDn, RDPn and RDNn is selected by the RD_INV bit (b3,
2. RMFn is always active high.
3. The active edge of RCLKn is selected by the RCK_ES bit (b4, RCF1,...).
相關PDF資料
PDF描述
IDT82P2828BHG IC LIU T1/J1/E1 28+1CH 640-PBGA
IDT82P2916BFG IC LIU T1/E1/J1 16CH SH 484BGA
IDT82P5088BBG IC LIU T1/E1/J1 OCTAL 256PBGA
IDT82V2041EPPG IC LIU T1/J1/E1 1CH 44-TQFP
IDT82V2042EPFG IC LIU T1/J1/E1 2CH SHORT 80TQFP
相關代理商/技術參數
參數描述
IDT82P2821BHG 功能描述:IC LINE INTERFACE UNIT 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 電信 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS 產品變化通告:Product Discontinuation 06/Feb/2012 標準包裝:750 系列:*
IDT82P2828 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:28(+1) Channel High-Density T1/E1/J1 Line Interface Unit
IDT82P2828BH 功能描述:IC LIU T1/J1/E1 28+1CH 640-PBGA RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
IDT82P2828BHG 功能描述:IC LIU T1/J1/E1 28+1CH 640-PBGA RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR)
IDT82P2916 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel High-Density T1/E1/J1 Line Interface Unit
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*