- 您現在的位置：買賣IC網 > PDF目錄1924 > IDT82P20416DBFG (IDT, Integrated Device Technology Inc)IC LIU T1/E1/J1 16CH SH 484BGA PDF資料下載
參數資料
| 型號： | IDT82P20416DBFG |
| 廠商： | IDT, Integrated Device Technology Inc |
| 文件頁數： | 35/121頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LIU T1/E1/J1 16CH SH 484BGA |
| 標準包裝： | 84 |
| 功能： | 線路接口單元（LIU） |
| 接口： | E1，J1，T1 |
| 電路數： | 16 |
| 電源電壓： | 1.8V, 3.3V |
| 功率（瓦特）： | 3.10W |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 484-LFBGA |
| 供應商設備封裝： | 484-CABGA（19x19） |
| 包裝： | 托盤 |
| 包括： | AIS 警報檢測器和發生器，回送功能，PRBS 發生器 / 檢測器，遠程檢測器和發生器 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁當前第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁
IDT82P20416
16-CHANNEL SHORT HAUL T1/E1/J1 LINE INTERFACE UNIT
Functional Description
20
December 17, 2009
3
FUNCTIONAL DESCRIPTION
3.1
T1 / E1 / J1 MODE SELECTION
The IDT82P20416 can be configured to T1/J1 mode or E1 mode
globally or on a per-channel basis. The configuration is determined by
the TEHWE pin, the TEHW pin and the T1E1 bit (b0, CHCF,...). Refer to
Table-1 for details of the operation mode selection.
3.2
RECEIVE PATH
3.2.1
RX TERMINATION
The receive line interface supports Receive Differential mode. In
Receive Differential mode, both RTIPn and RRINGn are used to receive
signal from the line side.
In Receive Differential mode, the line interface can be connected
with T1 100
, J1 110 or E1 120 twisted pair cable or E1 75
coaxial cable.
The receive impedance matching is realized by using internal imped-
ance matching or external impedance matching for each channel in
different applications.
3.2.1.1 Receive Differential Mode
In Receive Differential mode, three kinds of impedance matching are
supported: Fully Internal Impedance Matching, Partially Internal Imped-
ance Matching and External Impedance Matching. Figure-3 shows an
overview of how these Impedance Matching modes are switched.
Fully Internal Impedance Matching circuit uses an internal program-
mable resistor (IM) only and does not use an external resistor. This
configuration saves external components and supports 1:1 Hitless
Protection Switching (HPS) applications without relays. Refer to
Partially Internal Impedance Matching circuit consists of an internal
programmable resistor (IM) and a value-fixed 120
external resistor
(Rr). Compared with Fully Internal Impedance Matching, this configura-
tion provides considerable savings in power dissipation of the device.
For example, In E1 120
PRBS mode, the power savings would be
0.44 W. For power savings in other modes, please refer to Chapter 8
External Impedance Matching circuit uses an external resistor (Rr)
only.
Figure-3 Switch between Impedance Matching Modes
To support some particular applications, such as hot-swap or Hitless
Protection Switch (HPS) hot-switchover, RTIPn/RRINGn must be forced
to enter high impedance state (i.e., External Impedance Matching). For
hot-swap, RTIPn/RRINGn must be always held in high impedance state
during /after power up; for HPS hot-switchover, RTIPn/RRINGn must
enter high impedance state immediately after switchover. Though each
channel can be individually configured to External Impedance Matching
through register access, it is too slow for hitless switch. Therefore, a
hardware pin - RIM - is provided to globally control the high impedance
for all 16 receivers.
When RIM is low, only External Impedance Matching is supported for
all 16 receivers and the per-channel impedance matching configuration
bits - the R_TERM[2:0] bits (b2~0, RCF0,...) and the R120IN bit (b4,
RCF0,...) - are ignored.
Table-1 Operation Mode Selection
Global Programming
Per-Channel Programming
TEHWE Pin
Open
Low
TEHW Pin
Open
Low
(The configuration of this pin is ignored)
T1E1 Bit
(The configuration of this bit is ignored).
0
1
Operation Mode
T1/J1
E1
T1/J1
E1
IM
RTIP
RRING
RIN
R_TERM2
1 0
0 1
Receive
path
R_TERM[1:0]
RIM
R120IN
Rr = 120
相關PDF資料 |
PDF描述 |
|---|---|
| IDT82P20516DBFG | IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P2281PF | TXRX T1/E1/J1 LONG/SHORT 80-TQFP |
| IDT82P2282PF | TXRX T1/J1/E1 2CHAN 100-TQFP |
| IDT82P2284BB | TXRX T1/J1/E1 4CHAN 208-PBGA |
| IDT82P2288BBG | TXRX OCTAL T1/E1/J1 256-PBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT82P20416DBFG8 | 制造商:Integrated Device Technology Inc 功能描述:IC LIU T1/E1/J1 16CH SH 484BGA |
| IDT82P20416DBFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel Short Haul T1/E1/J1 Line Interface Unit |
| IDT82P20516 | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel Short Haul E1 Line Interface Unit |
| IDT82P20516BFBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel Short Haul E1 Line Interface Unit |
| IDT82P20516BFGBLANK | 制造商:IDT 制造商全稱:Integrated Device Technology 功能描述:16-Channel Short Haul E1 Line Interface Unit |
發布緊急采購，3分鐘左右您將得到回復。