- 您現在的位置：買賣IC網 > PDF目錄67712 > IDT5T9010BBI (INTEGRATED DEVICE TECHNOLOGY INC) 5T SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA144 PDF資料下載
參數資料
| 型號： | IDT5T9010BBI |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘及定時 |
| 英文描述： | 5T SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA144 |
| 封裝： | PLASTIC, BGA-144 |
| 文件頁數： | 6/23頁 |
| 文件大?。?/td> | 168K |
| 代理商： | IDT5T9010BBI |
14
INDUSTRIALTEMPERATURERANGE
IDT5T9010
2.5V PROGRAMMABLE SKEW PLL CLOCK DRIVER TERACLOCK
NOTES:
1. See RECOMMENDED OPERATING RANGE table.
2. For 1.8V LVTTL single-ended operation, the RxS pin is MID and
REF[1:0]/VREF[1:0] is left floating. If TxS is MID, FB/VREF2 should be left floating.
3. VDIF specifies the minimum input differential voltage (VTR - VCP) required for switching where VTR is the "true" input level and VCP is the "complement" input level. Differential mode
only. The DC differential voltage must be maintained to guarantee retaining the existing HIGH or LOW input. The AC differential voltage must be achieved to guarantee switching
to a new state.
4. VCM specifies the maximum allowable range of (VTR + VCP) /2. Differential mode only.
5. For single-ended operation in differential mode,
REF[1:0]/VREF[1:0] is tied to the DC voltage VREF[1:0]. The input is guaranteed to toggle within ±200mV of VREF[1:0] when VREF[1:0]
is constrained within +600mV and VDDI-600mV, where VDDI is the nominal 1.8V power supply of the device driving the REF[1:0] input. To guarantee switching in voltage range
specified in the JEDEC 1.8V LVTTL interface specification, VREF[1:0] must be maintained at 900mV with appropriate tolerances.
6. Voltage required to maintain a logic HIGH, single-ended operation in differential mode.
7. Voltage required to maintain a logic LOW, single-ended operation in differential mode.
8. Typical values are at VDD = 2.5V, VDDQ = 1.8V, +25°C ambient.
9. The reference clock input is capable of HSTL, eHSTL, LVEPECL, 1.8V or 2.5V LVTTL operation independent of the device output. (See Input/Output Selection table.)
10. This value is the worst case minimum VIH over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIH = 0.65 * VDD where VDD is 1.8V ± 0.15V.
However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated
worst case value ( VIH = 0.65 * [1.8 - 0.15V]) rather than reference against a nominal 1.8V supply.
11. This value is the worst case maximum VIL over the specification range of the 1.8V power supply. The 1.8V LVTTL specification is VIL = 0.35 * VDD where VDD is 1.8V ± 0.15V.
However, the LVTTL translator is supplied by a 2.5V nominal supply on this part. To ensure compliance with the specification, the translator was designed to accept the calculated
worst case value ( VIL = 0.35 * [1.8 + 0.15V]) rather than reference against a nominal 1.8V supply.
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE FOR 1.8V
LVTTL(1)
Symbol
Parameter
Test Conditions
Min.
Typ.(8)
Max
Unit
Input Characteristics
IIH
Input HIGH Current
VDD = 2.7V
VI = VDDQ/GND
—
±5
μA
IIL
Input LOW Current
VDD = 2.7V
VI = GND/VDDQ
——
±5
VIK
Clamp Diode Voltage
VDD = 2.3V, IIN = -18mA
—
- 0.7
- 1.2
V
VIN
DC Input Voltage
- 0.3
VDDQ + 0.3
V
Single-Ended Inputs(2)
VIH
DC Input HIGH
1.073(10)
—V
VIL
DC Input LOW
—
0.683(11)
V
Differential Inputs
VDIF
DC Differential Voltage(3,9)
0.2
—
V
VCM
DC Common Mode Input Voltage(4,9)
825
900
975
mV
VIH
DC Input HIGH(5,6,9)
VREF + 100
—
mV
VIL
DC Input LOW(5,7,9)
—VREF - 100
mV
VREF
Single-EndedReferenceVoltage(5,9)
—
900
—
mV
Output Characteristics
VOH
Output HIGH Voltage
IOH = -6mA
VDDQ - 0.4
—
V
IOH = -100
μAVDDQ - 0.1
—
V
VOL
Output LOW Voltage
IOL = 6mA
—
0.4
V
IOL = 100
μA
—
0.1
V
相關PDF資料 |
PDF描述 |
|---|---|
| IDT5T9010BBI8 | 5T SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA144 |
| IDT5T905PGGI | 5T SERIES, LOW SKEW CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO28 |
| IDT5T907PAGI | 5T SERIES, LOW SKEW CLOCK DRIVER, 10 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PDSO48 |
| IDT5T9110BBI8 | 5T SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA144 |
| IDT5T9110BBI | 5T SERIES, PLL BASED CLOCK DRIVER, 5 TRUE OUTPUT(S), 0 INVERTED OUTPUT(S), PBGA144 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| IDT5T9050PGGI | 功能描述:IC CLK BUFFER 1:5 200MHZ 28TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 產品培訓模塊:High Bandwidth Product Overview 標準包裝:1,000 系列:Precision Edge® 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:4 差分 - 輸入:輸出:是/是 輸入:CML，LVDS，LVPECL 輸出:CML 頻率 - 最大:2.5GHz 電源電壓:2.375 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VFQFN 裸露焊盤，16-MLF? 供應商設備封裝:16-MLF?（3x3） 包裝:帶卷 (TR) |
| IDT5T9050PGGI8 | 功能描述:IC CLK BUFF 1:5 200MHZ 28-TSSOP RoHS:是 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| IDT5T9050PGI | 功能描述:IC CLK BUFF 1:5 200MHZ 28-TSSOP RoHS:否 類別:集成電路 (IC) >> 時鐘/計時 - 時鐘緩沖器，驅動器 系列:- 標準包裝:74 系列:- 類型:扇出緩沖器（分配） 電路數:1 比率 - 輸入:輸出:1:10 差分 - 輸入:輸出:是/是 輸入:HCSL, LVCMOS, LVDS, LVPECL, LVTTL 輸出:HCSL，LVDS 頻率 - 最大:400MHz 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:32-VFQFN 裸露焊盤 供應商設備封裝:32-QFN（5x5） 包裝:管件 |
| IDT5T90533PGGI | 制造商:Integrated Device Technology Inc 功能描述:IC CLOCK BUFFER SDR 1:5 28TSSOP |
| IDT5T90533PGGI8 | 制造商:Integrated Device Technology Inc 功能描述:IC CLOCK BUFFER SDR 1:5 28TSSOP 制造商:Integrated Device Technology Inc 功能描述:IC CLK BUFFER 1:5 250MHZ 28TSSOP |
發布緊急采購，3分鐘左右您將得到回復。